دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Plastic instability in equibiaxial deformation of sheet metals
ناپایداری پلاستیک در تغییر شکل دو محوری متعادل ورقها
26833
FA
دکتر رضا
محمودی
Journal Article
1970
01
01
Plastic instability which results in the localization and failure of sheet metals has been
studied in equibiaxial stretching of commercial purity aluminium sheet. Attention was
focussed on two main industrial conditions of the material. These were representative of
the materials that could be processed by the commercial batchannealing process (slow
heating, long time) or by a continuous annealing process (fast heating, short time). The
instability strains were experimentally measured and compared with those predicted by
different instability criteria. The results have been analyzed on the basis of the
mechanical characteristics of the material under different conditions. It is concluded that
pressure instability can not be used as the extreme limit of forming and thus there is a
considerable amount of useful deformation after instability strain.
ناپایداری پلاستیک که منجر به تمرکز کرنش و شکست ورقهای تحت تنش می گردد در حالت تنش کششی دومحوری روی ورق آلومینیوم تجارتی مورد بررسی و مورد مطالعه قرار گرفته . کرنش در نقطه ناپایداری به صورت تجربی اندازه گیری شده و با نتایج حاصل از تئوری های مختلف ناپایداری مقایسه گردیده است . دلایل اختلاف تئوری و تجربه با توجه به خواص مکانیکی آلیاژ مورد استفاده مورد تجزیه و تحلیل واقع گردیده است . نتایج بدست آمده نشان می دهد که در تمامی حالات ، معیارهای ناپایداری پایان تغییر شکل مفید نبوده و همراه مقداری کرنش بعد از کرنش ناپایداری قابل حصول است این کرنش مفید حتی در مورد شرایطی از آلیاژ که درکشش تک محوری شکل پذیری اندکی داشته اند قابل ملاحضه بوده است .
https://jfe.ut.ac.ir/article_26833_4cc57ac6c2ba5dde052b59da3531412e.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Frame Alignment Procedure in Digital Transmission systems
تجزیه و تحلیل عملیات همزمانی فریم در سیستم های انتقال دیجیتال
26834
FA
دکتر ناصر
رضایی
مجید
صدری
Journal Article
1970
01
01
Every digital transmission system requires frame alignment. It is necessary to
identify the varius signal componets and to bring receiver into phase with respect to the
transmission format so that the digits can be properly assembled for demultiplexing. Fast
and reliable frame alignmant is important, and therefore has been a subject for study.
This paper a comprehensive analysis of frame alignment procedure used for time
division multiplex equiment complying with European standards (which is used in IRAN
and many other countries). The study complements the work of others on frame
alignment by presenting a more simplified method for understanding frame alignment
procedure. The approach derives the probability generating function of frame alignment
procedure from the generalized state transition diagram of Sitter. The probability
generating function is then used to estimate the average and variance of the timing
parameters. The principal transition times (out - of- frame detection time, maximum
average reframe time, false in - frame time and misframe time) is used as a performance
criteria for optimization of parameters. The effect of design criteria on various timing
parameters is presented graphically and a realistic example is considered.
در سیستم های انتقال دیجیتال برای تفکیک و بازیابی سیگنالهای دریافتی در گیرنده از عملیات همزمانی فریم استفاده می شود . عملکرد مطمئن و پاسخ سریع از پارامترهای اساسی فرایند همزمانی می باشد . در این مقاله یک تحلیل جامع از عملیات همزمانی فریم برای سیستم های ادغام کننده دیجیتال (با استاندارد اروپایی که در ایران نیز استفاده می شود ) ارائه شده است . با استفاده از چهار مشخصه زمانی و اساسی تعریف شده برای این سیستم ، عملکرد آن برای مقادیر مختلف پارامترهای مدار همزمانی بررسی شده است و به صورت دیاگرامهائی مناسب جهت طراحی ارائه گردیده است . سپس نتایج بدست آمده جهت طراحی یک سیستم خاص که هدف تحقیق بوده ، مورد استفاده قرار گرفته است .
https://jfe.ut.ac.ir/article_26834_8f0f139cc971696a899f6030a525a3ae.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Difficulties in the Treatment of Copper Porphyry Ores
مشکلات موجود درآرایش کانه های مس پرفیری
26835
FA
حسین نعمت
اللهی
Journal Article
1970
01
01
A high percentage of world copper production is obtained from porphyry copper
reserves, These reserves are characterized by: very high tonnage, greater horizontal
dimensions than vertical, association with stock like intrusion masses, dispersed minerals
in the porphyry mass and in its neighbor rocks, intense sericitization and inplace silicification.
The porphyry coppers are concentrated by flotation. The main problems in the
flotation of these ores are: slime, excessive pyrite, oxidized pyrite, oxide and oxidized
copper minerals,various of copper sulphide minerals and finally, operational parameters.
The present study deals with the effect of these trouble making factors in the flotation
process.
بخش بزرگی از مس تولیدی در جهان از منابع پروفیری تامین می شود . مشخصات کلی این منابع ذخیره زیاد ، عیار کم ، ابعاد بیشتر کانسار در جهت افقی تا در جهت قائم ، همراهی با توده های نفوذی استوک مانند ، جانشینی پراکنده در توده های پروفیری ، فلوتاسیون است . مشکلات عمده ای که در فلوتاسیون این کانه ها پدید آمده عبارتند از :
وجود نرمه , وجود پیریت بیش از حد , وجود پیریت اکسیده شده , حضور کانیهای اکسیده شده , حضور کانیهای اکسیده و اکسید شده مس , حضور انواع مختلف کانیها سولفوره مس در سنگ معدنی ، تغییرات سنگ معدنی در نقاط مختف معدن و سر انجام پارامترهای عملیاتی .
https://jfe.ut.ac.ir/article_26835_aea6e0cdca3ad9f84f698ba7647fdb62.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Numerical Analysis of Combined Refraction and Diffraction of Waves
بررسی عددی میدان موج تحت اثر ترکیب پدیده های انکسار و تفرق
26836
FA
دکتر خسرو
برگی
مهندس جواد
ملک
Journal Article
1970
01
01
Refraction and Diffraction combination of Waves, is very important and applicable
problem in coastal engineering (e.g. for designing break - water). However, formulation
of this phenomen and numerical solution is very difficult.
In this study, a numerical algorithm based on the mild Slop sea bed theory is
presented to obtain the appropriate governing equations of combined Refraction Diffraction.
Also, a software has been prepared to solve these equations by finite
difference method in time domain. Finally comparison of the differents results is shown.
پدیده های انکسار و تفرق در نزدیکی سواحل بویژه هنگام برخورد موج به سر موجشکن ها در ورودی حوضچه های بنادر ، و ترکیب این پدیده ها در داخل حوضچه از مسائل مهم در طراحی سازه های دریایی بشمار می روند . پیچیدگی پدیده های فوق و ترکیب آنها عملا مشکلات عمده ای در تامین مدل ریاضی مناسب و حل آنها پدید می آورد. در این مقاله نمونه ای از روش عددی بررسی دستگاه معادلات شیب ملایم تابع زمان با روش تفاوت های محدود که مدل ریاضی مناسبی برای ترکیب انکسار و تفریق امواج را بیان می نماییم ارائه شده است . بر اساس این الگوی عددی ، نرم افزار مربوط تهیه شده و میزان دقت نتایج در مقایسه با روشهای تحلیلی و سایر روش های عددی ، و یا به صورت کیفی مورد بررسی قرار گرفته و قابلیت های روش مورد بحث نشان داده شده است .
https://jfe.ut.ac.ir/article_26836_b6e22feba6347d962688491e9a42a700.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Two - Dimensional Temperature Field in a Semi-Infinite Finned Wall
میدان دو بعدی دما در دیوار نیمه بینهایت پره دار
26837
FA
دکتر مجید
ملکی
جمشید
محرری
Journal Article
1970
01
01
In this paper, two-dimensional heat transfer in a semi-infinite wall with fins of
rectangular profile has been investigated. The conduction equations of the wall and fins
are solved simultaneously by a numerical method. The principal parameters of the
problem are the fin spacing, length, and fin-to-wall conductivity ratio. In this
investigation, the effect of these parameters on two-dimensional temperature field of the
wall and the fins, and on the fin performance has been discussed. The results indicate
that the temperature depression caused by the multifin array is larger than that of the
single-fin arrangement. Moreover, reduction of the fin spacing, increase in fin length and
thermal conductivity all have an enhancing effect on temperature depression. Finally,
the fin performance is directly proportional to the length, spacing, and thermal
conductivity of the fins.
در این مقاله ، انتقال حرارت دو بعدی در یک دیوار نیمه بینهایت پره دار با پره های متعدد مستطیلی شکل بررسی شده است . معادلات هدایت در دیوار و پره ها به طور همزمان به روش عددی حل شده اند . پارامترهای اصلی مسئله عبارتند از فاصله پره ها ، طول آنها و نسبت ضرایب هدایت حرارتی پره به دیوار . در این بررسی اثر این پارامتر ها بر میدان دو بعدی دما در دیوار و پره ها و کارایی پره ها تشریح شده است . نتایج بدست آمده نشان میدهد که وجود پره ها ی متعدد دما بیش از آنچه که در دیوار تک – پره ای مشاهده شده است کاهش می دهد . همچنین کاهش فاصله پره ها ، افزایش طول آنها و ضریب هدایت حرارتی همگی کاهش دما را شدت می بخشند . و بالاخره ازدیاد فاصله ، طول و ضریب هدایت پره ها کارایی پره را تقویت می کنند .
https://jfe.ut.ac.ir/article_26837_08248e4eae42ec6fb198cca0023c141d.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Simulation Of Rotating Disk Contactors (ROC) For Industrial
and Semi . Industrial Processes
شبیه سازی برجهای استخراج RDC نیمه صنعتی و صنعتی
26838
FA
حسین
بهمنیار
پریسا
خدیوپارسی
Journal Article
1970
01
01
In order to simulate the rotating disk contactor all hydrodynamic parameters,
dispersed phase hold-up, characteristic velocity, mean drop size, drop size distribution,
axial mixing and mass transfer have been taken into account. Mechanisms of mass
transfer (stagnant, circulating, oscillating drops) were used in this study. Column height
found from effect of mean drop size and drop size distribution have been compared.
https://jfe.ut.ac.ir/article_26838_87ee29126b75e618678607edc385bbe8.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Two Dimensional Mathematical Model of Unsteady Flow in
Lakes and Estuaries Using Symmetrical Grid
مدل ریاضی دو بعدی جریان غیر ماندگار با استفاده از شبکه متقارن جهت بررسی هیدرولیک دریاها و دریاچه ها
26839
FA
حسین
سامانی
محمد علی بنی
هاشمی
Journal Article
1970
01
01
In this study, a method which is based on the integration of Navier-Stokes and
continuity equations has been used to develop the governing equations. In these
equations the Coriolis acceleration and the effect of wind also have been considered.
The main application of the model is to solve two dimensional problems with free
surface in the plane. The offshore engineering projects and the hydrodynamic problems
of lakes and estuaries can be mentioned as application examples of the model.
The required data are the geometry of the medium, bed roughness coefficient, wind
velocity and geographical coordinates of the medium. Since the problem to be solved is
basically unsteady, in addition to the boundary condition, initial conditions should also
be given.
Several numerical tests have been performed to check the model and quite
satisfactory results have been observed.
در این مقاله جهت بدست آوردن معادلات حاکم بر پدیده ، روشی بکاربرده شده است که مبتنی بر انتگرال گیری از معادلات" ناویه - استوکس" و پیوستگی می باشد . در معادلات فوق الذکر تاثیر عوامل مختلفی نظیر شتاب کوریولیس و روش باد در نظر گرفته شده اند .
جهت حل معادلات از روش " تفاضلهای محدود " استفاده گردیده و برخلاف مدلهای ریاضی موجود ، در این مدل " شبکه متقارن " بکار رفته است . کاربرد عمده مدل ، حل مسائل جریان با سطح آزاد حالت دو بعدی در صفحه است . بعنوان مثال پروژه های مهندسی سواحل و بنادر و مسائل هیدرود دینامیک دریاچه ها و دریاها را می توان ذکر کرد . داده های مورد نیاز مدل عبارتند از : مشخصات هندسی محیط ، مشخصات فیزیکی نظیر ضریب زبری بستر ، سرعت باد و مختصات جغرافیایی محیط با توجه به " غیر ماندگار" بودن مسئله علاوه بر " شرایط مرزی" ، " شناخت شرایط اولیه " نیز لازم است .
به منظور بررسی صحت و دقت مدل ، آزمایشهای متعددی در رابطه با جریانهای ماندگار انجام شده و نتایج خوبی بدست آمده است .
https://jfe.ut.ac.ir/article_26839_b2a37ffbf205cc5ef7063f02f90938ed.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
54
0
1986
11
22
Prediction of Retrograde Condensation Using the SRK Equation of State
پیش بینی RETROGRADE CONDENSATION با استفاده از معادله حالت SRK
26840
FA
محمد مهدی منتظر
رحمتی
شهرام
اسلامی
Journal Article
1970
01
01
The SRK two-parameter cubic equation of state has been used for the calculation
of the equilibrium constant using the liquid and vapor fugacity coefficients for three
binary mixtures. Dew and bubble points have been determined using the equilibrium
constants and the phase envelope has been plotted showing dearly that retrograde
condenstaion occurs.
The following percent deviations have been obtained from the experimental values:
8.2% for carbon dioxide - monochloromethane binary system, 4% for the ethane heptane
binary system, and 2% for the ethane - octane binary system.
In view of the above comparisons, it seems that the SRK equation of state is
capable of predicting retrograde behavior with good accuracy.
معادله حالت درجه سوم دو پارامتره SRK برای محاسبه ضریب تعادلی با استفاده از ضریب فوگاسیته در دو فاز بخار مایع برای سه مخلوط دو جزئی به کار رفته است . نقاط حباب و شبنم با استفاده از ضرایب تعادلی بدست آمده و نمودار فازی این مخلوطها رسم شده که حالت Rrtrograde Condensation در ان بوضوح مشخص است . درصد خطای میانگین برای مخلوط دو جزئی دی اکسید کربن – منو کلرومتان 8/2 درصد برای مخلوط دو جزئی اتان – هپتان حدود 4 درصد و برای مخلوط دو جزئی اتان – اکتان 2درصد میباشد . با توجه به این نتایج بنظر میرسد که معادله حالت SRK از توانائی و دقت نسبتا خوبی برای پیش بینی حالت Rrtrograde Condensation برخوردار است .
https://jfe.ut.ac.ir/article_26840_cfb581ebba78ddb490ee4481d9a5a620.pdf