دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Geothermal Energy
انرژی حرارتی زمین (1)
قسمت اول –معرفی موضوع
26549
FA
زین العابدین
نجات
Journal Article
1970
01
01
An introduction to geothermal energy is given III this article where the
techniques of research, exploration and utilization of source of energy will be
discussed in following articles.
This series of articles are the result of knowledge and experience gained
in Japan for the period of eleven weeks where the author benefited a scholarship through University of Tehran.
در قسمت اول مقاله منحصراً آشنایی با انرژی حرارتی زمین بعمل آمده است در مقالات بعدی روشهای مختلف اکتشاف و بهره برداری از جنبه های علوم و مهندسی مورد بحث قرار خواهد گرفت . لازم به تذکر است که مطالب ذکر شده از منابعی خلاصه شده که که در مسافرت یازده هفته ای نویسنده بعنوان ماموریت مطالعاتی از طرف دانشگاه تهران در ژاپن بدست آمده است .
https://jfe.ut.ac.ir/article_26549_e567eeacff7e21783d1fcea87c8caffd.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Stability of equilibrium. in nonlinear differential equations
پایداری تعادل در معادلات دیفرانسیل غیر خطی
26550
FA
دکتر نصرالله
تابنده
Journal Article
1970
01
01
In this article stability of equilibrium in the systems of nonlinear differential
equations is studied. Through several theorems and examples some criteria
for the stability of these systems are given. In this study we consider both
autonomous and nonautonomous systems.
در این مقاله در مورد پایداری تعادل در سیستم معادلات دیفرانسیل غیر خطی بحث شده است ضمن چند قضیه و مثال معیارهایی برای تعیین اینکه آیا این معادلات در نقطه به خصوصی پایدارند یا نه داده شده اند دراین مطالعه دستگاههای اتونوموس و غیز اتونوموس هر دو مورد بررسی قرار گرفته اند .
https://jfe.ut.ac.ir/article_26550_2c315d3849459ca7fc0cd2d6777321b8.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
A Least Square Mode Matching Technique for Waveguide iscontinuities
تطبیق دادن مدها در مسایل ناهمواری های میکرو موج توسط روش عددی کمترین مربع ها
26551
FA
همایون
عریضی
Journal Article
1970
01
01
The fields III various sections of a waveguide network are approximated
by their truncated modal expansions. The magnitude squared of each expression of the boundary conditions is integrated over the respective interfaces. The sum of these integrals is a quadratic function (called error function) of only the unknown modal amplitudes. The minimization of this function reduces to the solution of a linear equation which is directly obtainable from the boundary conditions. The unique minimum of the error function represents the best mode matching procedure in the least square sense. This technique is readily applicable to most waveguide discontinuity problems. However, it is applied here to the off- set junction of two parallel plate waveguides and two rectangular waveguides with mode and current probe excitations. A weighting factor which multiplies the error due to the magnetic field is investigated and conservation of real power is utilized as a criterion for its selection.
میدان الکترومغناطیس درون قسمت های مختلف یک شبکه میکروموج را توسط بسط عددی مناسب تقریب می کنیم تمام شرایط حدی را روی حدود و فصل مشترک مناطق می نویسیم و انتگرال مجذور اندازه هرکدام را بر روی سطوح فصل مشترک مناطق مختلف می گیریم . مجموع انتگرال ها را تابع خطایی می نامیم که تابع مثبت و درجه دوم ضرایب مدی است تابع خطایی فقط یک مینیمم دارد و برای بدست آوردن آن کافی است یک معادله خطی بر حسب ضرایب مدی مجهول حل کنیم این دسته معادله های خطی چند مجهولی را می توان مستقیماً از شرایط حدی بدست آورد تنها مینیمم این تابع خطایی بهترین راه تطبیق مدها را از نظر روش کمترین مربع ها می دهد این روش برای حل مسئله ناهمواریهای گوناگونی قابل استفاده می باشد در اینجا فقط از اتصال دو موج بر با صفحات موازی و دو موج بر با مقطع مستطیلی بحث می کنیم منبع تغذیه ممکن است مدی پخش شونده بوده و یا جریان برق سطحی (میله ای ) بر روی سطح مقطع موج بر باشد . عامل وزنی دلخواهی در خطای مربوط به شرط حدی روی میدان مغناطیسی ضرب می شود و در اینجا مورد بررسی قرار می گیرد و اصل بقای انرژی را بعنوان معیاری برای انتخاب این عامل بکار می بریم .
https://jfe.ut.ac.ir/article_26551_d0c4ab669e23348616de1e1c0df58108.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Earthing of TelephoDe EschaDge Office
PART ONE:
Measurement of earth resistivity by finding the voltage
distribution on its surface
زمین کردن مراکز تلفنی
قسمت اول :اندازه گیری مقاومت مخصوص زمین
26552
FA
یدالله
ارضی
Journal Article
1970
01
01
Nowadays for many purposes an earthing system in telephone exchange
office will be designed such as, transmission, protection and lessen the amount of crosstalk, so that is the reason why these kind of matters have put in an appearance seriously.
For example in the case of prositive pole of battery crosstalk will be
reduced. In telecommunication lines some of the speech currents may go from one line to the others through earth and as a result cause crosstalk. But if one of the poles of exchange battery is earthed, the path of leakage currents will be returned to the line and consequently reducing crosstalk.
The amount of earth resistance estimated to be below O. 5 n for the large
offices having a capacity about 10,000 subscribers and more.
It is common to say that acquiring this value is rather difficult referring
to the different kinds of soil.
In that case, a lot of countries prefere to design a system with a high
amount of resistance from the view point of economy. According to C. C. I. T. T. recommendations, measurements are shown that the lead sheath of cable are able to reduce it by 60- 90 per cent. But referring to the decision of cable factories, which are going to change lead sheath to PE, they will automatically be canceled.
For this reason designing a group electrodes will be very important.
There are many factors effecting upon earthing resistance, which among
them soil resistivity plays the main role.
To the best of the author's knowledge, the soil properties are very changeable
and not really under control.
To tell the truth estimation of future value IS the main difficulty upon
our designing.
In this article we've shown different methods for measuring earth resistivity and acquaintance with stratification of earth layers to find a suitable
method for selection of electrodes.
بررسی زمین کردن مراکز تلفنی از سال گذشته به این مرکز واگذار شده که امید می رود در آینده نزدیکی بتوان به تکمیل و ارائه روشهای مناسبی با در نظر گرفتن خواص گوناگون زمینهای ایران که به علت دگرگونیهایی در آب و هوای مناطق مختلف بطور ناشناخته ای باقی مانده است دست یافت .
امروزه به منظور کاهش کرس تاک قطب مثبت باطری مرکزی را زمین کرده که مقدار مقاومت آن به فشار گاسی و تماسی ارتباط دارد .
گرچه هنوز پیشنهادی ازطرف کمیته مشاوره بین المللی تلگراف و تلفن G.C.I.T.T. در مورد اندازه دقیق این مقامت داده نشده ولی بر طبق اندازه گیری های انجام شده و به خصوص با در نظر گرفتن استاندارد کشورهای مختلفه برای مراکز تلفنی بزرگ با تعداد مشترکین بیشتر از 10000 مقدار آن بایستی در حدود 5/0 اهم باشد .
برای رسیدن به مقاومت اخیر به نظر می رسد که اگر الکترودی به تنهایی دارای مقاومت زمین 50 اهم باشد با نصب حدود 100 الکترود به اندازه موردنظر دست خواهیم یافت .
متاسفانه به خاطر اثر متقابل الکترودها بر هم به تعداد به مراتب بیشتر از آنچه که ذکر گردید نیاز داریم در ایران بعلت طرحهای گسترده مخابراتی مراکز تلفنی گوناگونی در دست ساختن است که موازی با کارهای ساختمانی پروژه زمین آنها هم بایستی آماده گردد .
مشکلات کار بخصوص در آینده با تصمیم کارخانجات سازنده کابل که غلاف سربی را به پلاستیکی بدل خواهند ساخت بیشتر شده بطوریکه عملاً کابلهای مخابراتی در کاهش مقاومت زمین سهمی نداشته و نتیجتاً طرح یکی سیستم الکترود گروهی اهمیت فراوانی خواهد یافت .
مقاومت زمین الکترودهای کارگذاری شده در خاک عبارت از مقاومتی است که زمنی در قبال عبور جریان الکتریکی از خود نشان می دهد مبین این مقاومت ، مشخصه توزیع پتانسیل هادیها در مجاورت رویه بیرونیشان می باشد و بر روی این مشخصه عوامل گوناگونی تاثیر گذارده که عبارتند از :
جنس و شکل الکترود ، نحوه کارگذاری ، عمق کارگذاری ، فرکانس مدار و بالاخره مقاومت مخصوص خاک
از مهمترین این عوامل مقاومت مخصوص خاک است که در این قسمت به محاسبه توزیع آن در زمینها می پردازیم .
از آنجا که شرایط زمین را نمی توان به سهولت تحت کنترل قرار داد خواص بارز آن هرلحظه دشت خوش تغییر است این دگرگونیها باعث بالا رفت اندازه های مقاومت شده که نهایت به اشکالات انتقال منتج خواهد گردید .
بدینگونه طرح یک سیستم زمین به بررسی های دامنه داری در جهت شناخت عوامل مختلف و بالابرد ضریب اطمینان مدار نیاز دارد .
در مقاله اخیر روشهای اندازه گیری مقاومت مخصوص زمین و شناخت طبقات مختلفه آن آورده شده است .
https://jfe.ut.ac.ir/article_26552_a8fa3bd43a695a7561ad33ccb6a12f2c.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Mass Transfer With Simultaneous Chemical Reaction
کلیاتی درباره پدیده های انتقال جرم همراه با واکنشهای شیمیایی
26553
FA
مرتضی
سهرابی
طاهره
کاغذچی
Journal Article
1970
01
01
A phenomenon of mass transfer with chemical reaction takes place whenever
two phases which are not at chemical equilibrium with one another
are brought into contact. Such phenomena are made up of a number of elementary
steps, which may be summarised as follows.
(i) Diffusion of one or more reactants from the bulk of phase I to the
interface between the two phases.
(ii) Diffusion of the reactants from the interface towards the bulk of
phase 2.
(iii) Chemical reaction within phase 2.
(iv) Diffusion of reactants initially present within phase 2, and/or of
reaction products, within phase 2 itself due to concentration gradients which
are set up by the chemical reaction.
Steps (ii) , (iii) and (iv) may take place simultaneously, and thus mutually
interfere; the overall phenomenon resulting from steps (ii) , (iii) and (iv) takes
place in series with step (i). If step (i) is rate controlling, the overall rate is
not influenced by the chemical reaction, and the process may be regarded as a simple mass transfer phenomenon which is not influenced by the reaction rate.
The analysis of mass transfer with chemical reaction is of interest when
the overall phenomenon resulting from steps (ii), (iii) and (iv) is rate-controlling.
Chemical reactions which accompany mass transfer between phases are
usually classified as, slow, fast and instantaneous.
In this paper the" nature of these reactions is described and the mathematical
models related to such phenomena are presented and discussed.
در مقاله حاضر مبحث انتقال ماده همزمان با فعل و انفعال شیمیایی در مورد سیستمهای گاز-مایع با فرض آنکه واکنش در فاز مایع انجام شود مورد مطالعه قرار می گیرد معمولاً واکنشهای شیمیایی را که همراه با انتقال جرم صورت می گیرند با توجه به مکانیسم آنها به سه دسته کند ، سریع و آنی تقسیم می نمایند . در مورد واکنشهای کند می توان از تغییرات غلظت در حول سطح مشترک گاز –مایع صرفنظر نموده و در نتیجه غلظت ترکیب شونده موجود در فاز مایع را ثابت فرض کرد .
در فعل و انفعالات سریع زمان لازم برای واکنش شیمیایی خیلی کمتر از عمر متوسط عناصر سطحی بوده و در نتیجه مقیاس زمانی جذب شیمیایی به زمان نفوذ و یا به عبارت دیگر به شرایط هیدرودینامیکی فاز مایع بستگی ندارد در این حالت واکنش معمولاً در یک حوزه مشخص در داخل فاز مایع صورت می گیرد .
در واکنشهای آنی جسم نفوذ کننده و جسم موجود در فاز مایع نمی توانند در مجاورت یکدیگر به طور مستقل وجود داشته باشند و در نتیجه حوزه واکنش به یک صفحه محدود خواهد گردید که محل آن تابعی از ضرایب نفوذ دو ترکیب شونده می باشد .
در این مقاله کوشش کرده ایم تا کلیاتی درباره هریک از این واکنشها بدست داده شود و در هر مورد نیز معادلات ریاضی مربوطه را با در نظر گرفتن تئوریهای جدید پدیده نفوذ بدست آورده و مورد بحث قرار داده ایم .
https://jfe.ut.ac.ir/article_26553_bb08ba66695c8c197ed7ebf580b09454.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Transmission-loss Formula for Economic Dispatch Calculations
فرمول تلفات انتقال نیرو برای محاسبات دیسپاچینگ اقتصادی
26554
FA
فرخ حبیبی
اشرفی
Journal Article
1970
01
01
In economic dispatch study, when transmission-loss IS also considered,
partial differential derivatives of transmission-loss with respect to generating plant
output powers appear in the coordination equations. Obviously, an attempt for
expressing transmission-losses as a function of generating plant outputs simplifies
the calculations. In this paper a method based on Kron's six reference frames,
and Kirchmayers developments on the calculation of loss formula is described.
In a bus reference frame transmission network is expressed as:
E =z I
We have to eliminate the individual load currents as variables, since
the final result should involve only generator powers. First the sum of the load
currents is defined as a total equivalent load, and then it is assumed that each
load current remains a constant complex fraction of the total equivalent load.
By applying Kron's transformation theory to the equation (1) a new formulation
for the transmission network ;will be obtained which involves only generator
currents :
E=ZIG
The real losses of the transmission network may be calculated as follows:
PL=Re(E IG*)=Re(IG Z I *)=Re(i * ZI )
substituting IG=Id+j Ig and Z=R+jX into equation (3) and using the rules
of matrix theory results to :
PL=Id ( )Id+Ig ( )Ig-2Id ( )Ig
It is noted that only the symmetric past of the R and skew-symmetric part of
the X contribute to real loss.
Finally, to express PL in terms of generator powers J another transformation
is performed on the equeation (4) which puts PL into the desired form:
Pl=p BP
where the elements of B matrix are caned transmission-loss formula Coefficients.
Also procedures for representation of source-reactive characteristics and
representation of loads are briefly discussed.
برای اینکه در محاسبات دیسپاچینگ اقتصادی تلفات انتقال نیرو نیز گنجانده شوند لازم است تلفات انتقال بصورت تابعی از توان نیروگاههای سیستم در دسترس باشد . در این نوشته به کمک تئوری تبدیلات ابتدا سیستم نیروی برق را به شبکه معادلی که فقط حاوی مولد است تبدیل نموده و سپس با استفاده از این شبکه معادل فرمول برای تلفات انتقال نیرو بدست می آید که تابعی از توان مولدهای سیستم است ضمناً علاوه بر تحلیل ریاضی مسئله در هرجا که لازم به نظر میرسید راجع به شرایط واقعی که در عمل با آن روبرو هستیم توضیحاتی اضافه داده شده و سرانجام با طرح یک مسئله طریقه محاسبه ضرایب فرمول تلفات نشان داده شده است .
https://jfe.ut.ac.ir/article_26554_2656d395fe4d1613a86fd74d22e393af.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
A Comprative study of the Chemical State
of 32p and 35s in Potassium Chloride Crystals
مقایسه حالت شیمیایی گوگرد و فسفر در بلور کلرور پتاسیم
26555
FA
مسعود
کسرائی
Journal Article
1970
01
01
When potassium chloride is neutron irradiated in a reactor several nuclear
reactions take place. The following reactions have been most widely investigated:
(1) 35CI (n , p) 35s
(2) 35CI (n , a) 32p
In this article the chemical states of 32p and 358 have been compared using
the available litereture and some data obtained in this laboratory. The results
generally show that in no case a-reduced form of 32p is found in the irradiated
potassium chloride crystal. While in case of 358 reduced as well as oxidized
forms are observed. The results are interpreted in terms of the reactivity of
phosphorus and sulphur for electrons in the lattice.
هنگامیکه کلرور پتاسیم در راکتور هسته ای بمباران می شود 35S و 32P در اثر برخورد نوترون با 35CL به وجود می آید در این مقاله حالت شیمیایی این دو رادیوایزوتوپ در حالت جامد و محلول با هم مقایسه شده اند در عین حال اثر ناخالصی ها و پرتوهای یونیزه کننده بر روی تغییر حالت شیمیایی آنها مورد مطالعه قرار گرفته است چون تعداد اتمهای 35S و 32P به وجود آمده در شبکه کلرور پتاسم دریک تابش دهی معمولی نسبت به اتمهای ناخالصی و ناکاملی های بلوری ناچیز است اثر ناخالصی ها و ناکاملی ها می تواند بر روی تغییر حالت شیمیایی مورد بحث قابل ملاحظه باشد با توجه به نکات بالا چنین نتیجه گیری شده است که به طریق تئوری تنها نمی توان حالت شیمیایی این دو رادیو ایزوتوپ را پیش بینی کرد مقایسه حالت شیمیایی این دو رادیو ایزوتوپ نشان می دهد که در بیشتر حالات فسفر به حالت اکسید شده و گوگرد هم به حالت اکسید شده و به حالت احیا شده مشاهد شده است دلایلی که این اختلاف راتا حدی توجیه می کند ارائه شده است .
https://jfe.ut.ac.ir/article_26555_a32d53c24c4f865b3e2e7448f42cd22d.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Least Squares Adjustment with the use of Matrix Algebra
Method A: Observation Equations Summary
متد کمترین مربعات با استفاده از جبر ماتریس ها حالت (معادلات مشاهدات )
26556
FA
مهندس علی اصغر
شریفی
Journal Article
1970
01
01
Statistics has proved that when you increase number of observations
the mean of accidental errors goes to zero, in other words with statistical terms
we can say the expected value of accidental errors is zero
n
?i
E{?}=lim =0 .
n
Increasing the number of observed quantities will cause another problem, we will
have more equations than it is necessary to solve for unknown parameters.
Here is the point that mathematical solution differs from computation in
experimental sciences. The later method is the least squares solution. In this
me thod all the observed quantities are used in such a way that if we find
differences between observed quantities and the adjusted values of these quantities
(residuals), the sum of squares of residuals be minimum. We can summarize
this method by it's two major characteristics:
1-The solution is unique and independent of the path, and the order
of equations.
2 - The sum of squares of residuals is minimum.
The classic method of least squares (as we call it) can be found in such
books like geodesy, mathematical statistics, and numerical analysis. With the
application of matrix algebra we present the method of least squares adjustment
in different way, however the principle is the same, but it does have some
advantages. Let us summarize weaknesses of the classical method as bellow:
1 - With classical method computation is slow and uneconomical.
2 - The simultaneous adjustment of large networks is very difficult and
actualy imposible, therefore the network have to be devided in blocks, and
adjust each block respect to the previous one. This will cause a kind of controversy
with the first principle, because the final results depend on the path
and the starting point of adjustment.
3 - It is difficult to analyse the accuracy of computation, and the accuracy
of the adjusted values.
4 - Enforcing the effect of correlated observations (the effect of covariances)
is difficult and actually imposible.
In the method of least squares adjustment with the use of matrix algebra
most of the computations are systematic kind wich can be done by electronic
computers very fast. There are only two parts which shoud have to be found
or estimated by us:
1-To estimate a weight matrix (P) or variance-covariance matrix of
observations ( Lb= . P ) by the informations we have about instrument,
operator, and outer circumstances.
2-To find and write down a suitable mathematical structure (mathematical
model).
MATHEMATICAL MODEL
Mathematical model is some functions that exist between observations
and parameters. The mathematical model for observation equations is a special
kind, and that is when each observed quantity can be written as a function of
some parameters.
La=f(Xa)
Where X, is a vector of adjusted parameters with u components (number of
parameters), and La is avector of adjusted observations with n (number of
observations) components. The other notations that we are going to use are:
Xo , the initial approximate values of parameters chosen arbitrarily before
adjustment.
The differences of Xa, and Xo , or the variation of parameters are
X=X -X
The measured quantities are denoted by vector L with n components
using the following subscripts:
Lb , the measured values,
La' the adjusted values,
Lo , the values computed from values X, through the mathematical model
Lo=f(xo).
The differences of these sets are denoted as :
L=LO-Lb
V=La-Lb residuals.
We can rewrite the mathematical model (I) interms of L, and X,
Lb+V=F(Xo-X)
After expanding it we get
Lb+V=F(XO)+AX
where A is a matrix with n rows and u columns, the elements of A are partial
derivatives of measured quantities with respect to the parameters.
A
X =XO
Since
Lo=F(Xo), and L=Lo-Lb
equation (2) can be wirtten as
V=AX+L
The principle of lea
https://jfe.ut.ac.ir/article_26556_a62d77996924d8c56d929259c584c4ce.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
-
منشاء کانسارهای سرب و روی لایه ای شکل (1)
26557
FA
مرتضی مومن
زاده
Journal Article
1970
01
01
-
https://jfe.ut.ac.ir/article_26557_1f88b8497c4018468f1fce92de692ea4.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
La cODlparaison entre les systeDles
Acide-Base et oxydo-reducteur conjugues
مقایسه سیستم های اسید و باز مزدوج با سیستم اکسید و کاهش مزدوج
26558
FA
دکتر جمشید
مفیدی
Journal Article
1970
01
01
Les systemes conjugues (Acide-Base) ont ete connus depius longtemps
mais ses applications dans le domaine d'oxydo -vreducteur sont assez recentes .
Entre ces deux systernes, n'existent pas une analogie tot ale , et, on
remarque aussi des differences. Ci-dessous, details des analogies et des differences
sont constlatees.
1) analogies:
a) - Dans un systerne conjugue, si un corps est fort, celiu qui est conjugue
sera faible; c'est a dire, si l'acide est fort, la base conjuguee sera faible, ou, si
l'oxydant est faible, Ie reducteur conjugue sera fort.
b) -Dans les systemes conjugues, les solvants ant des roles analogues
(echanges d'ions ovec les solvants).
2) differences.
a) -La reaction d'echanges protons se fait assez rapidement, tandisque
celle d'electrons, se produit d'une facon plus lente, si bien que un oxydant ou
un reducteur tres fort peut exister en milieu aqueux.
b) -La reaction d'autoprotolyse est toujours reversible, et celIe d'autoredox,
suivat les cas, ont des valeurs relatives de constates d'equibbres grandes ou petites.
در این مقاله مقایسه ای بین سیستم های اسید و باز واکسید و کاهش از نقطه نظر کاربرد کلمه مزدوج به عمل می آید و سپس تشابهات و همچنین موارد اختلاف بین سیستم های اسید و باز مزدوج و سیستم های اکسید و کاهش مزدوج خاطر نشان می گردد .
https://jfe.ut.ac.ir/article_26558_d4e144ffe75ce5a919475c3c4441a00a.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Les ophiolites du zagros et les conditions de lour mise en place
افیولیت های زاگروس و چگونگی تشکیل آنها
26559
FA
حسین معین
وزیری
حسین
شیخی
Journal Article
1970
01
01
در منطقه خاورمیانه و در امتداد چین خوردگیهای آلپ توده هایی ادخالی متشکل از سنگهای اولترا بازیک و بازیک همراه با رادیولاریت ، سرپانتینیت و لاوهای آتشفشانی مشاهده می گردد که اصطلاحاً افیولیت نامیده شده است .
شرایط فیزیکو شیمیایی ماگمای ما در این سنگها همیشه مورد بحث و گفتگو بوده است در گذشته جایگزینی آنها را به صورت سرد و جامد و فقط ناشی از تکتونیک می دانسته اند در سالهای اخیر مشاهده هاله دگرگونی در حد فاصل افیولیتهای نیریز و آهکهای کرتاسه فوقانی عقیده جایگزینی ماگمای داغ و پر حرارت را در این منطقه قوت بخشیده است .
نتایجی که از مطالعه و و مقایسه اختصاصات کریستالوگرافی بلورهای اولیوین موجود در پریدوتیهای نیریز و بلورهای اولیوین موجود در آنکلاوهای پریدوتیتی بازالتها بدست آمده این نتیجه راعاید می سازد که ماگمای اولترابازیک دارای منشاء ازمانتو بوده و در موقع جایگزینیش در تشکیلات کرتاسه فوقانی حالتی نیمه مذاب داشته است .
https://jfe.ut.ac.ir/article_26559_9ce283a932a611d0e9f4d3133564d171.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
The Development of the Palazoic in South West Asia
توسعه و تکامل دوران اول زمین شناسی در خاور نزدیک
26560
FA
سهراب
شهریای
Journal Article
1970
01
01
https://jfe.ut.ac.ir/article_26560_d2b45358f68aac2d66e9a0fa24177236.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
Environment of Deposition and Sedimentary Petrology of the
Cambrian System in a Part of South Central Alborz, Iran
محیط رسوبی و سنگ شناسی رسوبات کامبرین در بخشی از جنوب البرز مرکزی
26561
FA
بیژن
اسفندیاری
Journal Article
1970
01
01
Faculty of Science, University of Tehran
For the purpose of this study 160 rock thin sections, as well as many
hand - specimens, were studied and examined. The Cambrian system in the
area is consisting of the Labun and the Mila Formations. R. L. Folk's classification
scheme have been used in the sedimentary petrologic study of the specimens.
General conditions of the sedimentary environment during the Cambrian
time has been described and interpreted.
The Labun Formation which is consisting of three members, has a
composition varying from quartzite to arkose, and its maturity is ranging from
mature to sub mature. Few local dikes of diabasic composition have been
recognized in this Formation. It is concluded that the environment of deposition
of this Formation was of oxidizing conditions and the deposits are of platform
kind.
The Mila Formation does not have complete outcrop of the four members
present in this area at every locality. This is mainly due to faulting, which
has caused the omission of some of the members of this Formation. Mila Formation
is a typical deposit of marine origin The conditions of deposition of this
formation was of varying depth and general reducing environment.
به منظور این مطالعه بیش از 160 مقطع میکروسکوپی و تعداد زیادی نمونه ماکروسکوپی مورد مطالعه قرار گرفته و بر اساس آن مشخصات شرایط رسوب گذاری و حوضه رسوبی زمان کامبرین در این ناحیه توصیف شده است نامگذاری سنگهای رسوبی در این مطالعه بروش فولک صورت گرفته است رسوبات کامبرین این ناحیه شامل تشکیلات لالون و میلا می باشد مطالعات نشان می دهد که در هنگام تشکیل این رسوبات شرایط اکسیدکنندگی در محیط حکمفرما بوده و همچنین عمق حوضه رسوبی بتدریج افزایش می یافته است این رسوبات رامی توان از نوع پلات فرم دانست .
تشکیلات میلا در این ناحیه در اثر گسل خوردگی به طور کامل دیده نمی شود بلکه بین بخشهای 1 تا 4 متغیر است بررسی سنگ شناسی آن نشان می دهد که در این ناحیه تشکیلات میلا شامل 38 قسمت مختلف می باشد این تشکیلات به طور مسلم رسوبات دریایی باعمق متغیر است و شرایط احیاکننده می باشد که عموماً در محیط احیاکننده و کم انرژی بر جای گذاشته شده اند .
https://jfe.ut.ac.ir/article_26561_7364f0e12fe2199caa9d96c19638da5f.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
-
آینده نگری و اهمیت برنامه ریزی
26562
FA
ناصر
توحیدی
Journal Article
1970
01
01
-
https://jfe.ut.ac.ir/article_26562_d008013f1dedf66a41ea22f9a16c3a92.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
-
استفاده مجدد از فاضلابها –پس آبها –آبهای مصرف شده
26563
FA
مرتضی
حسینیان
Journal Article
1970
01
01
-
استفاده مجدد از فاضلابها –پس آبها و آبهای آلوده مساله ای است که مدتها پیش ذهن کارشناسان آب شناسی و مهندسین بهداشت را که مستقیماً مسئول تامین آب مورد نیاز اجتماعات هستند بخود مشغول داشته است . علت مهم توجه به این موضوع پیشرفتهای سریع صنعتی و افزایش جمعیت و بالا رفتن سطح بهداشت عمومی بیشتر نقاط دنیا بوده و در نتیجه مستقیم این پیشرفتها بالا رفتن میزان مصرف آب می باشد با توجه به محدود بودن منابع آب و در دسترس قرار نداشتن آبهای با کیفیت خوب و یا آبهایی که بتوان بااعمال ساده و صرف هزینه های کم از آنها برای پیشرفتهای یاد شده استفاده نمود مسئله بکاربردن فاضلابها 0پس آبها و آبهای آلوده پس از تصفیه مورد توجه قرار گرفته است .
در نوشته زیر سعی شده تا حدود زیادی موضوع فوق الذکر از نظر تاریخچه و نقاطی که طرح استفاده مجدد از فاضلابهای احیا شده در آنها در حال اجرا است و همچنین مشکلاتی که در مصرف مجدد فاضلابهای احیا شده وجود دارد مورد مطالعه قرار گیرد .
https://jfe.ut.ac.ir/article_26563_1c3c69d8fb326e71f45a9f544dc39d14.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
-
بررسی مسائل موجود در مهندسی متالوژی
26564
FA
دکتر جمشید
کامران
Journal Article
1970
01
01
-
در این مقاله سعی شده است مسایلی را که در کارخانه های متالوژی وجود دارد و همیشه مدیران فنی و مهندسان کارخانه را بخود مشغول می دارد مطرح می سازیم باید تذکر داد که هدف اصلی این مقاله یادآوری به طراحان و مدیران کارخانه های ریخته گری است به این معنی که موضوعهای بحث شده گرچه در شمار مشکلات لاینحل نیستند و فقط به توضیحات کوچکی نیاز دارند ولی هرکدام از این توضیحات خود مسئله پیچیده ایست که باید در مورد آن فکر کرد و جواب لازم را پیدا کرد .
البته این جوابها نمی توانند قاطع باشند و بستگی به عوامل مختلفی دارند که بر حسب شرایط ممکن است متفاوت باشند و این خود بر دشواری امر می افزاید امید است در این مقاله جوابهایی را که تا حد امکان پاسخگوی اشکالات موجود به خصوص در شرایط ایران باشد داده شود .
نباید فراموش کرد که در اکثر رشته های مختلف صنعتی فشاری که به مغز کارگر می آید به اندازه رشته ذوب فلزات نیست و عواملی که در آن موثرند با رشته های دیگر فرق دارد . مثلاً معایبی را که در ضمن کارهایی مثل تراشکاری و فلزکاری ظاهر می شود فوراً در حین کار می توان از بین برد و یا تصمیمی برای حذف آن در نظر گرفت در صورتیکه در ذوب فلزات با وجود اینکه به تمام نکات و مسایل توجه شده باشد و ظاهر محصول هم نشانه هایی که حاکی از عیب باشد نداشته باشد با این حال پس از مدتی کار با قطعه ریخته شده معایب آن ظاهر و آنرا از حیز انتفاع ساقط می سازد گذشته از این معضلات مسایل اقتصادی نیز به شدت ذهن متخصصین ذوب فلزات را به خود مشغول میدارد لذا پروژه عمل بسیار مهم می باشد و در روی آن باید دقت بسیاری معمول داشت . حال به طرح هریک از تشکیلات کارخانه می پردازیم .
https://jfe.ut.ac.ir/article_26564_e7c87dca2827c974c2c659e8a057d91d.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
-
از رویدادهای علمی و صنعتی جهان
26565
FA
محمد علی
رحمتی
Journal Article
1970
01
01
-
https://jfe.ut.ac.ir/article_26565_4a388446ff1ceacdc3424c0cdb2c8298.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
30
0
1974
12
22
-
واژه هایی چند به زبانهای فارسی ، انگلیسی ، فرانسه ، و آلمانی بری قسمتهای الکترونیک –راه و ساختمان – مهندس شیمی معدن و ذوب فلزات
26566
FA
Unknown
Journal Article
1970
01
01
-
https://jfe.ut.ac.ir/article_26566_aa51a099c3ccdcf61ed99475ebd3751b.pdf