دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
The Fresnel Zone Plate Antenna as an Electromagnetic Field Focusing Element.
آنتن صفحه ای مناطق فرنل یک عنصر متمرکز کننده امواج الکترومغناطیس
26414
FA
دکتر فرخ
آرزم
مهندس علیرضا
شوشتری
Journal Article
1970
01
01
Fresnel zone plate antenna (FZPA) was considered as a
recieving antenna. An expression of electric field on axis
of antenna produced by an incidente plane wave was
found . The expression was used for calculation of gain,
efficiency and optimum phase correcting function. Several
FZPA are fabricated and tested. Experimental and
theoretical results were compared and it was shown that
there was a good agreement between them.
در این مقاله مفاهیم اصلی آنتنهای صفحه ای فرنل مانند تابع تصحیح فاز ، بازدهی و بهره به صورت دقیق با روشی متفاوت بررسی شده است سپس با بکار بردن جریانهای معادل مغناطیسی و اصل هم ارزی یک بیان برای میدان ناشی از یک موج صفحه ای تائید شده بر آنتن در نقطه کانونی بدست آمده است این بیان برای بدست آوردن بازدهی و میدان روی محور آنتن و بهره بکار رفته است و نتایج این تحلیل تجربی مقایسه شده است .
https://jfe.ut.ac.ir/article_26414_68c9624674b1bb7a41ba86d4406b9c95.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Branches Passing Through Infinity in the Root Locus Method
شاخه های گذرنده از بی نهایت در مکان هندسی ریشه ها
26415
FA
دکتر محمد زاده
عیدگاهی
مهندس محمد قوام
زاده
Journal Article
1970
01
01
In this paper, construction rules of the root locus of a
positive feedback system whose loop transfer function is
not strictly proper have been investigated.
The root locus method is being used since 1950. It is
demonstrated that some of the steps in this technique are
not general and for a positive feedback system whose
loop transfer function is not strictly proper are not valid.
To overcome this problem, new definitions for root
locus branches have been presented which divide them
into branches passing through infinity and branches
ending/starting at/from infinity.
We have also considered the realization and stability of these systems.
در این مقاله روش رسم مکان هندسی ریشه ها برای سیستمهای فیدبک مثبتی که درآنها درجه صورت و مخرج تابع تبدیل حلقه با هم برابرند مورد تحلیل و بررسی قرار گرفته است این مقاله نشان می دهد قواعد ارائه شده برای رسم مکان هندسی ریشه ها که از دهه 1950 تا کنون مورد استفاده می باشند جامعیت ندارند و برای سیستمهای فیدبک مثبت دارای تابع تبدیل حلقه معمول صادق نمی باشند و باید برخی از این قواعد دوباره تعریف شوند .
در این مقاله تعریف جدیدی برای شاخه های موجود در مکان هندسی ریشه ها ارائه شده است و با تقسیم کردن شاخه ها به دو دسته شاخه های گذرنده از بی نهایت /بازگردنده به/از بی نهایت ،قواعد ارائه شده در منابع مختلف کنترل طوری اصلاح شده اند که در برگیرنده این گروه خاص از سیستمها نیز باشند .
در پایان سیستمهای مطروحه در این مقاله از دیدگاه تئوری های تحقق و پایداری مورد بررسی قرار گرفته اند.
https://jfe.ut.ac.ir/article_26415_fbd7758bd450cdac00c4d57e4a1ce4a9.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Rehabilation and Its Position in Construction Industry
بهسازی و جایگاه امروزی آن در صنعت ساختمان
26416
FA
دکتر مهدی
قالیبافیان
Journal Article
1970
01
01
In this paper, after definition of "Rehabilation" and a four
other key .words , a brief explanation of different types of
rehabilation is presented and other related concepts are
defined as well.Maintenance as a concept to reduce
Rehabilation and to announce the need of Rehabilation is
discussed. The question: "if the rehabilation is a necessity
or an arbitrary action" is argued toward the answer that
rehabilation is required to prevent the destroying effect of
time and it is an art as old as human. It is shown that the
logic is supported by the concepts used in the new
generation of seismic design codes. Finally, a step by step
algorithm is developed and demonstrated.
در این مقاله پس از تعریف بهسازی و چند کلید واژه دیگر ضمن شرح مختصر انواع بهسازی و گستره آن هرجا ضرورت ایجاب کرده تعاریف سایر واژه های مصطلح در امر بهسازی داده شده اند تا تفهیم و تفاهم تسهیل گردد در ادامه مقاله نگهداری به منظور تقلیل نیاز به بهسازی و اطلاع از نیاز به بهسازی مورد اشاره قرار گرفته و این سوال مطرح شده که بهسازی یک ضرورت است یا یک تفنن ؟و پاسخ داده شده است که بهسازی ضرورتی است برای مقابله با اثر فرساینده زمان و برای از بین بردن اثرهای سوء ، سوانح و حوادث ، هنری است به قدمت انسان و ضرورتی برخاسته از نیاز غریزی او به احساس امنیت که با نیازهای امروزی جوامع بشری دایر بر حفظ محیط زیست و سرمایه ملی کشورها نیز هماهنگی دارد علاوه بر این صراحت نسل جدیدی آئین نامه های طراحی ساختمانها در برابر زلزله دایر بر پذیرش بروز خرابی در ساختمانها در موقع زلزله ها شدید در قسمتهایی که به مثابه "فیوز" عمل می کنند و تعمیر این قسمتها پس از اینکه زلزله از سرگذشت مهر تائید دیگری بر ضرورت بهسازی زده است در آخر مقاله اصول و مراحل تهیه و اجرای طرحهای بهسازی شرح داده شده ، ماهیت زد و خوردی کار بهسازی یادآوری و نتیجه گیری شده است که باید با تمهیداتی موثر نیاز به بهسازی را حتی المقدور کم کرد و رهنمودهایی برای دستیابی به این منظور ارائه گردیده اند .
https://jfe.ut.ac.ir/article_26416_f69f399d8ab9e1e82b618061d27f3ef3.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Debottlenecking of Heat Exchanger Networks with Fixed Pressure Drops (l.Targeting)
اصلاح شبکه مبدلهای حرارتی به منظور رفع گلوگاه با در نظر گرفتن محدودیت های افت فشار 1-هدف گذاری
26417
FA
دکتر محمد حسن پنجه
شاهی
مهندس مهران غفوریان
صدیق
Journal Article
1970
01
01
Retrofit of Heat Exchanger Networks for energy saving
and/or debottlenecking is one of important aspects of
process engineering. Pinch Technology, as the most
efficient tool for the analysis of these networks, has been
applied to hundreds of such projects and shown
satisfactory results. However, all the existing methods for
debottlenecking, using Pinch Technology, are either
based on assumed heat transfer coefficients or corrected
ones on the bas is of revised conditions. This usually
causes problems in the plant hydro dynamic system, when
pressure drop constraints are present. In this paper the
new area algorithm, which is based on fixed stream
pressure drops and has previously been used in energy
saving retrofits, is incorporated into de bottlenecking
procedure and a new targeting method is introduced. The
method is then applied to a Crude Oil Distillation Unit ,
with 20% increase in throughput, and the results are discussed.
https://jfe.ut.ac.ir/article_26417_f7fcfdaef0d59f675b9be8d0c2191b0e.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Determination of Equilibrium Parameters and Effective Pore Diffusion Coefficient of Light and Liquid N-Paraffins on SA Molecular Sieves.
تعیین پارامترهای تعادلی و ضریب نفوذ موثر نرمال پارافین های سبک در فاز مایع ، در غربالهای مولکولی 5A
26418
FA
مهندس شهره
فاطمی
مهندس ایرج
شعاعی
Journal Article
1970
01
01
The molecular sieves are selective adsorbents. They can
adsorb some kind of molecules that are different in size
or shape from the others. In separation of n-paraffins
from iso-paraffins and aromatics, SA molecular sieve is
the suitable adsorbent, and can adsorb n-paraffins to
separate them from other hydrocarbons.
In this paper equilibrium isotherms of n-CS, n-C6 and
n-C7 from an inert solvent, benzen (non adsorbed), on
SA molecular sieves, was determined, for single
component adsorption. The experimental data was
conducted on the Langmuir Isotherm and the parameters
of this model were determined.
On the other hand , the kinetics of adsorption of n-C6
and n-C7 have been determined in the finite bath
experiments; and the concentration profile of each
component versus time was determined.
The batch adsorption model based on pore diffusion
model had been written and calculated numerically. There
were film and pore diffusion resistances against the
n-parrfin adsorption, and also there was local equilibrium
between the pore fluid and the solid phase. The
equilibrium model was based on the Langmuir Isotherm.
By super position of batch adsorption model onto
finite bath experiments, the tortousity factor of adsorbent
structure and the film mass transfer were estimated.
By determination of tortousity factor , the pore
diffusion coefficient of each component was calculated.
This procedure is a general method to determine the
effective pore diffusion coefficient of any component into
the adsorbents.
یکی از پارامترهای لازم جهت شبیه سازی و طراحی واحدهای جذب سطحی تعیین ضریب نفوذ موثر ماده جذب شونده به درون حفرات جاذب می باشد ضریب نفوذ موثر به دو عامل ضریب نفوذ مولکولی ماده و فاکتور پیچیدگی جاذب بستگی دارد فاکتور پیچیدگی یک جاذب به ساختمان کریستالی و شکل حفرات داخلی آن بستگی دارد و برای هر نوع جاذب مقداری مخصوص به خود است که برای تعیین آن باید از اطلاعات آزمایشی بهره گیری کرد .
درمقاله حاضر مدل ریاضی جذب سطحی در سیستم ناپیوسته برای جذب تک جزئی در دمای ثابت در شرایط زیر نوشته شده است :
دانه های جذب کروی و همگن هستند مکانیسم نفوذ ماده به داخل حفرات از نوع نفوذ حفره ای می باشد و میان سیال داخل حفرات و فاز جذب شده تعادل برقرار است و ارتباط غلظتها در فاز جذب و سیال داخل حفره در این حالت با کمک مدل تعادلی "لانگمیر" بیان شده است بطوریکه پارامترهای ایزوترم لانگمیر با تطبیق اطلاعات آزمایشی برای نرمال پارافینهای C5 تاC7 در فاز مایع بدست آمده است .
مدل جذب به روش عددی تفاضلهای محدود غیر صریح حل شد که نتیجه حل مدل تعیین تغییرات غلظت نرمال پارافین در توده سیال بر حسب زمان می باشد مجهول این مدل ضریب نفوذ حفره ای و ضریب انتقال جرم فیلمی می باشد که هدف تعیین کردن آنهاست به این وسیله با تطبیق نتایج حاصل از مدل و نتایج حاصل از آزمایش ضریب نفوذ موثر ماده به درون حفرات تعیین می گردد و در نتیجه می توان فاکتور پیچیدگی غربال مولکولی 5A را بدست آورد روش ارائه شده روشی است کلی که می توان به وسیله آن فاکتور پیچیدگی را برای انواع جاذبهای مختلف تعیین کرد .
https://jfe.ut.ac.ir/article_26418_726df81b882d754ee23002f94afe8f5a.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Effect of AI on the Hot deformation of Ferrite in Cu-Mn Steels.
اثر آلومینیوم بر فرآیند بازیابی دینامیکی فولادهای حاوی مس و منگنز
26419
FA
دکتر حسن
فرهنگی
دکتر عباس نجفی
زاده
مهندس سیامک
اخلاقی
Journal Article
1970
01
01
Effect of small Al additions, from 0.14% to 0.31% AI, on
the hot deformation behavior of low carbon steels
containing 1%Cu-1.2%Mn was investigated In the
temperature range of 750-800•C over the strain rate range
of 1O.3.1O.1s•1 by a hot compression testing machine. The
flow curves obtained, exhibited typical characteristics of
dynamic recovery type of softening mechanism, and the
critical strain to steady stat e flow and the steady state flow
stress decreased with increasing temperature and /or
decreasing strain rate . Furthermore, increasing AI
additions, led to higher critical strains and higher flow
stress levels and dynamic recovery was retarded. This
effect of AI, in the presence of Cu and Mn alloying
elements, is contrary to the previous reports on the
individual effect of AI, showing promotion of dynamic
recovery with increasing Al content in low carbon steels.
Scanning electron microscopy study of final
microstructure showed that deformation of initial grain
structure into a pancaked shape, formation of more or
less equiaxed subgrains, and dynamic precipitation of
second phase particles on the grain boundaries, as well as
the subboundaries were the main microstructural changes
associated with hot deformation of steels under
consideration in ferrite phase region.
اثر آلومینیوم از 14/0 تا 31/0 درصد وزنی بر رفتار گرم فولادهای کم کربن حاوی MN%2/1 –CU %1
با استفاده از آزمایشهای فشار گرم در محدوده حرارتی 800-750 درجه سانتی گراد در فاز فریت و محدوده نرخ کرنش 1S- 10 مورد تجزیه و تحلیل قرار گرفت بر اساس نتایج بدست آمده فرآیند نرم شدن حاکم در حین تغییر شکل گرم برای این آلیاژها فرآیند بازیابی دینامیکی است در این شرایط نشان داده شد که افزایش درجه حرارت و یا کاهش نرخ کرنش باعث کاهش کرنش شروع حالت پایدار و تنش سیلان حالت پایدار می گردد به علاوه افزایش درصد آلومینیوم بازیابی دینامیکی را به تاخیر انداخته و کرنش شروع حالت پایدار و تنش سیلان حالت پایدار را افزایش می دهد این اثر آلومینیوم در کنار عناصر آلیاژی CU,MN با گزارشهای قبلی درمورد اثر انفرادی آلومینیوم در به جلو انداختن فرآیند بازیابی دینامیکی متفاوت است مطالعه و مقایسه ساختار میکروسکوپی اولیه و ساختار میکروسکوپی نهایی به کمک میکروسکوپ الکترونی پویشی نشان می دهد که کشیده شدن دانه های اولیه تشکیل دانه های فرعی تقریباً هم محور و راسب شدن دینامیکی ذرات فاز دوم غنی از CU بر روی مرزهای اصلی و فرعی از تحولات اصل ساختار میکروسکوپی در حین تغییر شکل گرم است .
https://jfe.ut.ac.ir/article_26419_86df866095e155f50a3b8403789daf8b.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
haracterization and Beneficiation of Semnan Kaolin
شناسایی و شستشوی اولیه کائولن سمنان
26420
FA
دکتر منوچهر
اولیازاده
مهندس محمود
درویشیان
Journal Article
1970
01
01
There are many small kaolin deposits In Iran , which are
extracted and used in ceramic industry without any
treatment.
This investigation was aimed to study the ore and to
find whether a fine material can be produced for paper
usages.
The ore was studied by XRD, DTA, Optical and
scanning microscopy. Physical properties, such as
brightness were also examined. The main minerals ,
presented in Semnan kaolin, were kaolinite , quartz, iron
minerals and micas. Bleaching and high gradiant magnetic
separation were employed to reduce iron content and to
improve brightness. The results of HGMS were
encouraging as the brightness was increased from 63.4%
to 78.6%. Cationic flotation was used to decrease free
silica and abrasion index. The results were not positive at this stage.
ذخایر کوچک و متنوعی از کائولن در ایران وجود دارد. یکی از این ذخایر کائولن سمنان است که پس از استخراج بدون فرآوری در صنایع سرامیک به مصرف می رسد هدف از مطالعات حاضر شناسایی کامل مائولن سمنان و بررسی امکان فرآوری و مصرف آن در صنایع مختلف به خصوص کاغذ سازی بود .
با استفاده از روشهای پراش اشعه ایکس ، تجزیه حرارتی ،میکروسکوپ نوری و الکترونی در ابتدا کانیهای موجود و سپس خواص فیزیکی (سفیدی ،دانه بندی )کائولن سمنان بررسی شدند با توجه به میزان اکسید آهن آزمایشهای شیمیایی و جدایش مغناطیسی با گرادیان بالا برای جدا کردن ناخالصیهای رنگین و بهبود سفیدی کائولن سمنان انجام شد نتایج جدایش مغناطیسی موفقیت آمیز بود برای جدایش سیلیس آزاد و کاهش سایندگی کائولن سمنان از فلوتاسیون کاتیونی استفاده شد نتایج برای دانه بندی 53-10 میکرون رضایت بخش نبود .
https://jfe.ut.ac.ir/article_26420_0ec4f56a78f0942a9d889495995b464e.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Koenenite Synthesis and Its Genesis
سنتز کوئننیت Koenenite"" برای دستیابی به شرایط تشکیل آن
26421
FA
دکتر سهیلا
اصلانی
Journal Article
1970
01
01
Koenenite=[Mg7AI4(OH)22]4+.[Na4(Ca,Mg)2CI12]4- , is a
typical non-silicate clay mineral of oceanic salt deposits
which also widely occurs in salt clay, anhydrite, halite, and
potash-bearing rocks. Koenenite is found as an
undesirable sludge-forming component in the processing
of potassium salts .
Koenenite was first reported, in 1902, as an impurity
in a fairly pure halite from the Justus! potash mine, near
Volpriehausen/Sollingen in northern Germany. Since
NaCI was considered to be presented only as halite, the
chemical composition of koenenite was wrongly given as
2MgCl2 5Mg(OH)2 Al(OH)3 . But an accurate
composition of the mineral should be given as 4NaCI
4(Ca, Mg)Cl2 5Mg(OH)2 4AI(OH)3 . At present time,
koenenite is the only naturalIy occuing basic Mg-AI
chloride (Plus additional NaCI).
The initial experiments for the synthesis of koenenite
was carried out in 1982, in the system
NaCI-MgCl2-CaCl2-Al2O3-MgO-(H2O) at temperatures
between 2OO•C and 5OO•C and a pressure of one kilobar.
It was observed that firstly, the chemical composition
of the choride layer could range from [Na4 (Ca,
Mg)2CI12]4- to [Ca4?2CI12]4-, and secondly, it is possible to
form calcium-free koenenite.
Finally, in 1985 synthesis of Ca-free koenenite was
successfully carried out by the author at temperatures of
zoo' C-4OO• C and pressures of 1oo-1000 bars, in the
following two systems:
1.NaCI-MgClz-Al2O3-MgO-H20
2.NaCl-MgCI2-H2O-Ul(1)
کوئننیت با فرمول شیمیایی 4NACL.4(CA,MG)CL2.5MG(OH)2.4AL)OH)3.8,3H2O و یا
[NA4(CA,MG)CL12]4-[MG7AL4(OH)22]4++ متعلق به گروه کانیهای نمکی و خاکهای رسی غیر سیلیکاتی می باشد و در سیستم تریگونال متبلور می شود در کانسارهای نمکی همراه رسهای نمکدار ،انیدریت ،هالیت و نمکهای پتاسم یافت می گردد .
بنیان ساختار شبکه این نمک از تکرار متناوب دو لایه شبه بروسیتی تشکیل می شود یکی از لایه ها هیدروکسید آلومینیوم –منیزیم [MG7AL4(OH)22]4++ و دیگری لایه کلروری [NA4(CA,MG)2CL12]4- . این دو لایه در جهت [0001] بطور متناوب تکرار می شوند و اتصال این دو لایه یک پیوند هیدروژنی می باشد O-H….CL))
سنتز این کانی در سیستمهای زیر انجام گرفت :
الف :NACL-MGCL2-CACL2-MGO-AL2O3-(H2O)
ب:UI-NACL-MGCL2-CACL2
(که در اینجا UI?[MG7AL4(OH)22]4++.[CL4.4H2O]4- محصول دگرسانی کوئننیت می باشد )
شرایط سنتز هیدرترمال با فشار بین 3 تا 1000 بار و حرارت بین 90 تا 400 درجه سانتی گراد بود .
https://jfe.ut.ac.ir/article_26421_bc5f8aca4be71e82c6d4edc09319f8cf.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
An Experimental Investigation on Fiat Plate Inducer
بررسی تجربی یک ایندیوسر صفحه صاف
26422
FA
دکتر سید احمد
نوربخش
مهندس وحید
مهجوری
Journal Article
1970
01
01
One of the most problems that limits use of
turbomachines at high speed applications is cavitation.
Cavitation can damage casing and blades of turbopump,
also can make unstability in system.
Inducer that was installed in front of main impeller can
improve cavitation characteristic of system and increase
static pressure just before entrance of centrifugal pump.
Specially in fuel feed system of liquid propellant rockets
and airplanes that designer forced to make smaller
components with better performance, inducer is
commonly used.
Here to find the effect of viscosity in flow field of inducer,
water was selected. With use of an experimental test rig,
characteristic chart of Q-H (Flow rate - Head) and axial
distribution of walI static pressure were shown. The last
curve, implicitly showed the effects of Q on cavitation
characteristic of flat plate inducer.
A comparison between these results and previous
papers in this subject was made and the effect of blade's
number on cavitation characteristic was shown.
کاویتاسون به عنوان یکی از عوامل محدود کننده دور و ارتفاع مکش توربوپمپها می تواند باعث افت فشار خوردگی مکانیکی و ناپایداری در سیستم اینگونه از ماشینها شود .
ایندیوسرکه خود یک نوع توربوماشین است در جلوی چرخ اصلی پمپ مورداستفاده قرار گرفته و یکی از راههای عملی جهت کاهش و یا رفع این اثرات می باشد این ماشین به خصوص در سیستمهای تغذیه سوخت موتور هواپیما و نیز راکتورهای سوخت مایع به جهت لزوم بالا بردن دور و افزایش نسبت قدرت به وزن بکار رفته است .
بررسی پارامترهای ایندیوسر در جهت بهبود مشخصه های آن چه از لحاظ کاویتاسون (ماهش ارتفاع مکش مورد نیاز ) و چه هیدرولیکی (بهبود بازده ) منجر به انجام تحقیقات در جهت شناخت میدان جریان سیال در این نوع ماشین شده است .
جهت بررسی بهتر از این نوع پارامترها بر خلاف اغلب محققان که از سیال هوا استفاده کرده اند سیال آب انتخاب شد تا اثرات لزجت بهتر بتوانند موردبررسی قرار گیرند با کمک مدار آزمایشی که توسط نگارنده طراحی و ساخته شد نتایج تجربی بدست آمد این نتایج شامل مشخصه Q-H و نیز توزیع فشار متوسط استاتیک روی دیواره داخلی ایندیوسر بود که اثر آبدهی را به طور مستقیم بر ارتفاع و بطور ضمنی بر مشخصه کاویتاسون این توربوماشین نشان می دهند .
توضیح و تفسیر نتایج این دو منحنی با توجه به آزمایشات و نتایج تئوری محققان پیشین انجام پذیرفت و با استفاده از پارامترهای بی بعد معمول اثر تعداد پره بر مشخصه کاویتاسیون این ایندیوسر بدست آمده است در این میان به اثر نشتی لبه ای نیز پرداخته شد .
https://jfe.ut.ac.ir/article_26422_7482a3fcbba39221a3a8401c13da3e35.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Physical and Mathematical Principle of the Exper imental Method of Caustics in Re-Entrant Corners
گسترش مبانی ریاضی روش تجربی کاستیک (سایه نگاری ) در گوشه های مقعر
26423
FA
دکتر ناصر
سلطانی
مهندس وحید متین
فر
Journal Article
1970
01
01
In this paper, the experimental method of caustics and its
application to stress field and related studies in fracture
mechanics is described. Theocaris [1,2,3] has used the
optical method of caustics to study stress intensity factors
and the stress field around crack tips, in cracked
transparent plates.
Many other researchers have also used this method to
obtain stress intensity factors for different crack shapes in
different materials. But a review of the available literature
indicates that this method has not yet been used to study
the singularities in plates with notch or re-entrant
corners.
The stress field at the roots of sharp notches has
singularities of order A-l where A. depends on the notch
angle. In this study the essential equations and
parameters for the application of the method of reflected
caustics to V-notched plates were developed . The
equations obtained showed that the radius of the initial
caustic curve was not a constant and depended on 8.
It has also been shown that in many instances the
variation of initial curve with respect to 8 is relatively
small and can be ignored.
روش نوری کاستیک جهت مطالعه میدان تنش در حوالی نک ترکها و تعیین ضرایب شدت تنش توسط تئوکریس ارائه شده است در گوشه های مقعر بر خلاف ترکها روابط مکانیک شکست شکل پیچیده تری به خود می گیرند و مرتبط ساختن آنها با روابط حاصله از تحلیل شکست نور بسادگی مسله ترکها نیست .
هدف از این مقاله گسترش و بررسی مبانی ریاضی روش تجربی کاستیک در گوشه های مقعر جهت مطالعه میدان تنش در حوالی ریشه گوشه ها برای تعیین ضرایب شدت تنش می باشد .
در این مقاله با استفاده از تئوری مکانیک شکست الاستیک خطی و مرتبط ساختن آن با تئوری شکست نور در مواد شفاف معادلات لازم برای بررسی شدت تنش در گوشه ها بدست آمده است معادلات حاصله نشان می دهد که شعاع منحنی اولیه کاستیک ثابت نبوده و به متغیر موقعیت ? وابسته است حل معادلات نشان می دهد که این وابستگی در بسیاری از موارد اندک می باشد بطوریکه که می توان از آن صرف نظر نمود .
https://jfe.ut.ac.ir/article_26423_81ba265565744291197bd503c9c1ea00.pdf
دانشکده فنی
نشریه دانشکده فنی
0803-1026
57
0
1996
05
21
Determinat ion of Temperature Distribution Around a Moving Heat Source
تعیین توزیع دمای حاصل از چشمه های متحرک حرارتی
26424
FA
دکتر حسین
شکوهمند
مهندس مجید
ایزدخواه
Journal Article
1970
01
01
In this paper, the temperature distribution around a
moving heat source had been investigated including the
phase change and non phase change .
In non-phase change state, the governing equation
was converted to finite difference equation by finite
volume method and the equation was solved by
alternating direction implicit method. This method was
unconditionally stable .
In phase change state, the problem was formulated by
enthalpy function and finite difference equation was
solved with the explicit method because of the stability
criteria.
The effect of source heat, source velocity, preheat
temperature, variable physical properties, on
temperature distribution were examined, also their effect
on melting pool width and heat affected zone were
investigated. The application of these concepts in industry
was explained
در این مقاله توزیع دما در اطراف چشمه های متحرک حرارتی و نحوه انتقال حرارت از آنها به محیط جامد اطراف به صورت دو بعدی با در نظر گرفتن حالت تغییر فاز مورد مطالعه قرار می گیرد .
هدف از این مطالعه ارائه یک تحلیل مناسب برای جریان حرارتی حاصل از چشمه های متحرک و تعیین تاریخچه توزیع دما زمان و سرد شدن در جامدات مختلف است برای این منظور ابتدا معادلات حاکم و شرایط مرزی بیان شده و سپس روش حل بکار رفته ارائه گردیده است آنگاه نتایج حاصل با نتایج تجربی موجود مقایسه گشته اند و به علاوه تاثیر پارامترهای مهم در این فرآیند مورد بررسی قرار گرفته است .
https://jfe.ut.ac.ir/article_26424_ea62fcf1737d4ad0eef382adbcfcac81.pdf