@article { author = {حمیدی, علی اصغر and پایاب, حسن}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Mathematical model for a pilot scale iron ore pellet in duration furnace has been developed which considers the process of indurations including the reactions of limestone, magnetite and carbon. The differential equations of energy, mass and momentum were solved simultaneously. The profiles of temperature, pressure and concentration were obtained. The validity of the model has been checked by performing separate experiments on sub processes such as drying, firing and cooling. At first, a mixture of iron ore was selected and then the percentage of lime stone was changed. The maximum metallization and fired pellet strength with minimum sticking vs. basisity was obtained. In the next stage the percentage of carbon in iron ore is altered and all of physical and chemical property of the pellets was measured. Finally, the optimum percentage of carbon in the iron ore was determined. By using different percentage of carbon in the pellet the experiments were performed in three conditions. In the first condition, inlet gas temperature was decreased alone. In the second condition, inlet gas temperature and total indurations time were decreased together and in the third condition, in addition to above conditions; oxygen injection to the furnace was carried out. Energy savings in all three conditions have been obtained.}, keywords = {}, title_fa = {مدلسازی و بررسی افزایش تولید و کاهش مصرف انرژی در تهیه گندله در صنایع فولاد}, abstract_fa = {مدل ریاضی در پایلوت پلنت واحد گندله سازی با در نظر گرفتن واکنشهای سنگ آهک، مگنتیت و کربن در گندله ارائه می شود. معادلات دیفرانسیل جرم، انرژی و مومنتم بصورت همزمان حل می شوند. تغییرات درجه حرارت فشار و غلظت بر حسب ارتفاع بستر با نتایج تجربی مراحل مختلف شامل خشک شدن، پخت و سرد شدن گندله ها مقایسه می شوند. درصد سنگ آهک در گندله تا حصول بازیسیته مناسب (B4) و حداکثر احیاپذیری و حداقل چسبندگی تغییرات داده می شود. برای افزایش تولید و کاهش مصرف انرژی در سه حالت از کک استفاده شده است. در حالت اول ا افزودن مقادیر مختلف کک به گندله درجه حرارت گاز ورودی به بستر کاهش داده می شود. در حالت دوم علاوه بر کاهش درجه حرارت زمان گندله سازی نیز کاهش داده می شود. در حالت سوم علاوه بر موارد مذکور تزریق اکسیژن به کوره نیز انجام می شود و میزان پتانسیل افزایش تولید و کاهش مصرف انرژی معین می گردد.}, keywords_fa = {افزایش تولید,سنگ آهن,کاهش انرژی,کک,گندله سازی,مدلسازی}, url = {https://jfe.ut.ac.ir/article_10233.html}, eprint = {https://jfe.ut.ac.ir/article_10233_3bdbe2fb55ef7d361dd6fcdf18216d90.pdf} } @article { author = {رضائیان, ایرج and محمدی, امیرحسین and ایوانی, جواد}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Liquid polysuiphide is one of the polymers widely used as a sealent in the industry.The most important factors determining the physical, mechanical and chemical properties of polysulphide sealents are their cure system and temperature. There are various cure systems for liquid polysuiphides. The most suitable cure system is chosen by the robber compound composition and the final use of the product. Magnesium dioxide lead peroxide and sodium dichromate are used as cure agents for liquid polysulphide. Magnesim dioxide is also used as a cure agent for liquid polysulphide sealers in airplane fuel tank. In these two part sealers the composition of the formulation is the most important parameter for optimum results. A study on the effect of these sealers composition on their physical and mechanical properties shows that each component can have different effect on these properties according to their cure system. In this investigation the experimental results for physical and mechanical properties of polysulphide sealers samples were analyzed by Tagouchi method. Finally a cure system which gives the optimum physical and mechanical properties is suggested.}, keywords = {}, title_fa = {بررسی سیستم پخت دی اکسید منگنز، بر خواص آمیزه های پلیمر پلی سولفاید مایع}, abstract_fa = {یکی از انواع پلیمرهائی که در صنعت ساخت درگیرها مورد استفاده می باشد، پلی سولفاید مایع است. سیستم پخت و درجه پخت از مهمترین عوامل تعیین کننده خواص فلیزیکی، مکانیکی و شیمیائی درزگیرهای پلی سولفایدی هستند. این پلیمر مایع دارای سیستم های پخت متنوعی می باشد که بنابر سیستم پخت و اجزاء آمیزه متناسب با آن نوع مصرف نهائی آنها تعیین می گردد. عمده ترین عوامل پخت این پلیمرهای مایع عبارتند از دی اکسید منگنز، پراکسید سرب و دی کرومات سدیم. دی اکسید منگنز یکی از عوامل پخت این درزگیرها است که استفاده از آنها را در مخازن سوخت لاستیکی هواپیما میسر می سازد. اجزاء فرمولاسیون در جهت دستیابی به خواص مطلوب، یکی از اساسی ترین مسائل در رابطه با ساخت این درزگیرهای دو جزئی است. بررسی میزان تاثیر این اجزاء روی خواص فیزیکی و مکانیکی آمیزه ها نشان می دهد که هر کدام از این اجزاء بنابر سیستم پخت مورد استفاده تاثیرات متفاوتی بر این خواص دارند. در این تحقیق، آزمایشات توسط روش تاگوچی طراحی شده اند و آزمون های خواص فیزیکی و مکانیکی بر روی همه آمیزه ها انجام گردیده و نتایج حاصل مورد مقایسه و تجزیه و تحلیل قرار گرفتند. در انتها سیستم پختی که توسط آن بهینه ای از خواص فیزیکی و مکانیکی حاصل گردید ارائه شده است.}, keywords_fa = {اکسیداسیون,پلی سولفاید,درزگیر,سیستم پخت,طراحی آزمایشات}, url = {https://jfe.ut.ac.ir/article_10234.html}, eprint = {https://jfe.ut.ac.ir/article_10234_b1a0c7c8203e5267e3bc835cd9294073.pdf} } @article { author = {رضائیان, ایرج and مددی, جمشید and ایوانی, جواد}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {The choice of suitable coatings based on Nitrocellulsoe with suitable properties such as adhesion, scratch resistance and hardness for ABS plastics are of special importance. In this research work, surface preparation of ABS was carried out using solvent and oxidation methods. Lsopropyl alcohol was used as solvent and sulphochromic acid was used for oxidation method. The choice of coatings with suitable adhesion and hardness based on different percentages of nitrocellulose with short alkyd resins were tested. The results show that a 50/50 mixture of nitrocellulose with alkyd resins provides the best adhesion, gloss and hardness properties for these coatings.}, keywords = {}, title_fa = {فرمولاسیون و بهینه سازی پوشش های مناسب بر روی پلاستیک ABS}, abstract_fa = {دستیابی به پوشش هایی با خواص مناسب برای اعمال بر روی سطوح ABS با چسبندگی خراش پذیری و سختی مناسب بر پایه رزین نیتروسلولز از اهمیت ویژه‌ای برخوردار می باشد. در این تحقیق آماده سازی ABS به دو روش حلالی و اکسایشی انجام شد که در روش حلالی از ایزوپروپیل الکل و در روش اکسایشی از سولفوکرومیک اسید استفاده گردید. برای ایجاد یک پوشش با چسبندگی و سختی مناسب بر روی ABS درصدهای مختلف از رزین نیتروسلولز با الکید کوتاه مورد آزمایش قرار گرفت. نتایج نشان داد که نسبت یک به یک از رزین نیتروسلولز با الکسید کوتاه بهترین خواص را از نظر سختی براقیت و چسبندگی دارد.}, keywords_fa = {اکریلونیتریل بوتادی ان استایرن ABS,پوشش,خمیر رنگ,دمای انتقال شیشه ای Tg,رزین الکید کوتاه روغن بر پایه نارگیل,رزین نیتروسلولز}, url = {https://jfe.ut.ac.ir/article_10235.html}, eprint = {https://jfe.ut.ac.ir/article_10235_f2fb97fd75e0a442758e52e3f26d4cd1.pdf} } @article { author = {رضائیان, ایرج and هاشمی, سید جلال الدین and ایوانی, جواد}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Anew and simple method for direct and simultaneous determination of traces of Fe, V, Cu, Ni, Zn, Cr, Al, Mg, Ca and Mn in petroleum crudes, mineral oils and petroleum products is described. Graphite powder was used as spectroscopy buffer and for preparation of standard powders. Using naked carbon electrode and cone shaped counter electrode, a steady D.C arc discharge was obtained with graphite matrix. Aquartz spectrograph of high resolution was used for this study.}, keywords = {}, title_fa = {استفاده از طیف سنجی قوسی برای تعیین مقادیر جزئی فلزات موجود در نمونه هائی از نفت خام ایران}, abstract_fa = {بکارگیری روش طیف سنجی قوسی در تعیین مقادیر جزئی فلزات موجود در نمونه های نفت خام، یک روش ساده جدید در تعیین مستقیم و همزمان مقادیر جزئی فلزات Fe , Cu, V, Al, Cr, Mg, Zn, Ca, Mn در نفت خام روغنهای نفتی و فراورده های نفتی می باشد. از پودر گرافیت بعنوان بافر طیف سنجی و نیز جهت تهیه پودرهای استاندارد استفاده گردید. در این روش با استفاده از یک الکترود گردنه دار کربن و یک الکترود شمارنده مخروطی شکل، یک تخلیه الکتریکی قوسی پایدار D.C توسط ماتریس گرافیت صورت می گیرد. از یک طیف نگار کوارتز با قدرت تفکیک بالا، برای این بررسی استفاده گردیده است.}, keywords_fa = {الکتروکربن,پلاک عکاسی,پودر گرافیت,خطوط طیفی پودر استاندارد,دانسیتومتر,طیف سنجی قوسی}, url = {https://jfe.ut.ac.ir/article_10236.html}, eprint = {https://jfe.ut.ac.ir/article_10236_65b5b1855cdddd7a59ea1ae87063b382.pdf} } @article { author = {زاهدی, سیدمحمد رضا and فراهانی, فرهنگ جلالی}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {In the present study, one of the important EOR processes solvent injection, which can cause severe asphaltene precipitation was considered. One of the main causes of precipitation is the disturbance of thermodynamic conditions of the reservoir fluid. In research center of Ahwaz Petroleum University, a series of experiments were conducted using glass beads contained slim tubes to find out the effect of experimental variables such as solvent ratio, injection flow rate and temperature alteration on the injection pressure build up and permeability impairment. In this simulation, by using the conditions of experimental runs, a compositional and single porosity model was built using the CMG package in which a new fluid characterization model using Winprop module was used and the following results were obtained: The most affecting parameter on asphaltene precipitation was solvent ratio with direct effect; the speed of asphaltene precipitation was increased by increasing the injection flow rate and the temperature variation has a minor effect on this process.}, keywords = {}, title_fa = {بررسی تئوریک و مطالعه شبیه سازی پدیده رسوب آسفالتین در محیط متخلخل در پروسه تزریق حلال}, abstract_fa = {یکی از تکنیک های متداول در پروسه ازدیاد برداشت تزریق حلال می باشد. تزریق بعضی از حلالها در مخازن باعث بهم خوردن تعادل ترمودینامیکی و تغییرات ترکیب درصد اجزای نفت مخزن شده و موجبات تشدید رسوب دهی آسفالتین و عواقب ناشی از آن را پدید می آورد. بدلیل اینکه رسوب آلی اجزای سنگین نظیر آسفالتین، باعث افزایش فشار تزریق کاهش بسیار شدید تراوایی خلل و فرج، گرفتگی و مسدود شدن محیط متخلخل، تغییر خاصیت ترشوندگی سنگ مخزن و در نهایت کاهش تولید شده، بنابراین قبل از شروع پروسه تزریق، مطالعه عمیق و جامع علمی و عملی برای بررسی و پیشگویی تشکیل رسوبات آسفالتین با توجه به شرایط مخزن، نوع حلال تزریقی، نسبت حجمی حلال به نفت و همچنین دبی تزریق امری لازم و ضروری بنظر می رسد. در این مطالعه، با شبیه سازی یک سری از آزمایشات تزریق نرمال هپتان در یک محیط متخلخل (لوله قلمی) با استفاده از سیال یکی از مخازن جنوبی ایران (اهواز) رابطه رسوب دهی دینامیک آسفالتین و اثر تغییر پارامترهای آزمایشگاهی (تغییر نسبت حجمی حلال به نفت تزریقی، دبی حجمی تزریق و دما) بر روی افزایش فشار تزریق و کاهش تراوایی مخزن مورد مقایسه قرار گرفته است. در این مدل با استفاده از شبیه ساز ترکیبی GEM از مجموعه نرم افزاری CMG مدل تخلخل یگانه مخزن (single) و ساخت مدل سیال مخزن توسط نرم افزار Win Prop، شرایط لوله قلمی برای یک مخزن فرضی مدل شده و نتایج خروجی شبیه ساز در هر سناریوی تعریف شده مورد بررسی قرار گرفت. با توجه به نتایج شبیه سازی و ثابت بودن همه شرایط مدل، مهمترین پارامتر اثرگذار بر رسوب دهی آسفالتین، تغییر نسبت حجمی نرمال هپتان به نفت بود که افزایش آن باعث رسوب دهی شدیدتر آسفالتین و افزایش فشار تزریق و کاهش بیشتر تراوایی مخزن می شد. اثر تغییر دبی حجمی تزریق، در سرعت رسوب گذاری بود و تغییر دما اثر چندانی نداشت. با توجه به نکات ذکر شده در فوق، لازم است در انتخاب بهترین نسبت حجمی حلال به نفت تزریقی، نهایت مطالعه و دقت بکارگرفته شده تا از مشکلات رسوب دهی آسفالتین در مخزن تا حد امکان پیشگیری شود.}, keywords_fa = {آسفالتین,تخلخل,تراوایی,حلالیت,دما و فشار بحرانی,رزین,رسوب دهی,فوگاسیته,مخازن نفتی,مخزن اهواز,میسل}, url = {https://jfe.ut.ac.ir/article_10237.html}, eprint = {https://jfe.ut.ac.ir/article_10237_fd10bcd95798bfb535c5051cc3720edb.pdf} } @article { author = {فاطمی, شهره and مهر, امین سعادت}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {In the present article, the mathematical modeling of multi-component hydrocarbon adsorption in a fixed bed of granular activated carbons, with different shapes, was carried out numerically. The model can predict the behavior of adsorption of hydrocarbon mixtures in the air flow, as a transient function of time and as a function of bed length and particle radius with respect to bed axial dispersion, external film resistance and pore diffusion mechanism inside the particle according to equilibrium adsorption isotherm of Extended Langmuir on the solid surface. This model can predict the breakthrough curves at different operational conditions of temperature, pressure, inlet concentrations, and flow velocity for adsorption and desorption cycles. Orthogonal Collocation and Implicit Finite Difference Method are respectively, implemented for numerical solution of PDEs in particles and packed bed, for the mixtures of ethane, propane, n-butane and n-pentane in air. To ensure from the accuracy of the model, hydrocarbon fractional uptake of the adsorbent was calculated by the model and was compared with experimental results found in by literature. The results show a good fitness of model and experiments. The sensitivity of analysis was studied by changing the model parameters such as particle size, tortuosity factor of adsorbent, gas flow rate and temperature. The results exhibit high dependency to the particle size and tortuosity factor. Also, the breakthrough curves of purging the bed by pure air flow was studied at different flow rate in order to predict the time of bed regeneration.}, keywords = {}, title_fa = {مدلسازی ریاضی جذب دینامیک و چند جزیی هیدروکربنهای سبک در بستر ثابت کربن فعال}, abstract_fa = {در این مقاله مدلی ریاضی برای جذب چند جزئی هیدروکربنها در بسترهای جذب شامل دانه های جاذب با اشکال مختلف ارائه شده است و می تواند جذب سطحی مخلوطی از هیدروکربنهای موجود در جریان هوا را به صورت گذرا و به صورت تابعی از ابعاد بستر و جاذب با در نظر گرفتن مقاومت نفوذ محوری در بستر و مقاومت انتقال جرم فیلمی اطراف دانه و با استفاده از مکانیسم نفوذ حفره ای در داخل دانه همراه با شرایط جذب تعادلی در سطوح جامد ارائه کند. مدل جذب تعادلی بکار رفته مدل غیر خطی و چند جزیی لاتگمیر توسعه یافته می باشد که بر حسب نوع کربن فعال بکار رفته می تواند در شرایط عملیاتی مختلف دما، فشار، غلظت اجزا و سرعت جریان گاز، منحنی گذر را در شرایط جذب و دفع بستر پیشگوئی کرده و ظرفیت جذب کربن فعال را برای هیدروکربنهای مختلف در شرایط فوق ارائه دهد. برای حل همزمان معادلات بستر و دانه از روشهای تعامد تطبیقی در دانه و تفاضل محدود غیر صریح در بستر به صورت همزمان استفاده شده است. منحنی کسر ماده جذب شده در دانه (FU) و منحنی گذر حاصل از حل مدل برای مخلوطهایی از اتان، پروپان، نرمال بوتان و نرمال پنتان بدست آمده است. برای اطمینان از صحت مدل، نتایج حاصل از منحنی (FU) با نتایج آزمایشی انجام شده در مراجع در شرایط یکسان مقایسه گردیده است که نتایج از دقت خوبی برخوردار است. در بررسی منحنی گذر، پاسخ بستر جذب نسبت به تغییر پارامترهای موثر مدل از جمبه اندازه دانه فاکتور پیچش جاذب، سرعت جریان گاز و دما تعیین و مورد ارزیابی قرار گرفته و همچنین زمان پر شدن بستر و میزان ماده جذب شده به ازاء واحد جرم جاذب در شرایط مختلف تعیین و بررسی گردیده است. مدل حاضر نشان می دهد که میزان جذب شدگی به اندازه دانه و نیز فاکتور پیچش جاذب وابستگی زیادی داشته و جذب توسط مکانیسم نفوذ حفره ای کنترل می شود. همچنین منحنی گذر در شرایط بازیابی بستر نیز در اثر ورود هوای خالص به بستر پر شده بررسی و زمان بازیابی بستر با توجه به سرعت جریان هوا تعیین گردیده است.}, keywords_fa = {تعامد تطبیقی,جذب سطحی,کربن فعال,کنیستر,منحنی گذر,هیدروکربن}, url = {https://jfe.ut.ac.ir/article_10238.html}, eprint = {https://jfe.ut.ac.ir/article_10238_4452b90413aa6d6c4a63a87461d4b9a5.pdf} } @article { author = {مغربی, مرتضی and خدادادی, عباسعلی and آقابابازاده, رویا and اکبرنژاد, محمدمهدی and ایوانی, جواد}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Nanostructured tungsten carbide powder is a new product in nanotechnology, and it may substitute platinum in many catalytic reactions, due to its exceptional properties. Here, the effect of temperature and heating rate on carburization and phase transition of ammonium paratungstate has been studied. The ammonium paratungstate was carburized in 20% CH4 in H2 atmosphere in a quartz reactor. The temperature of the reactor was increased with different slopes of 0.33 and 1.0°C/mm. The samples were weighed and characterized by XRD, SEM, BET and density measurement in 50-100°C intervals during the carburization. Results indicate the formation of amorphous carbon and metallic tungsten and surface area rising at about 550°C. At higher temperatures, up to 950°C, the tungsten is converted to W2C and then to WC, without significant changes in its specific surface area. The amount of amorphous carbon shows a minimum at about 750°C that seems to be due to methanation of the carbon .As compared to 1.0, the 0.33°C/mm heating rate does not change the nanostructures considerably, except in the 750-850°C temperature range. However, the 0.33°C/mm heating rate preserves the pristine microstructures of the ammonium paratungstate more than 1 .0°C/mm heating rate.}, keywords = {}, title_fa = {تهیه پودر کاربید تنگستن نانوساختاری و مطالعه مشخصات آن در حین کربوریزاسیون}, abstract_fa = {پودر کاربید تنگستن نانوساختاری یکی از محصولات جدید نانوفناوری بوده و به دلیل خواص استثنایی خود به عنوان جایگزین پلاتین در واکنشهای مختلف مطرح شده است. در این تحقیق اثر دما و نرخ افزایش دما روی مشخصات و تغییرات فازی کاربید تنگستن نانوساختاری حاصل از سنتز پاراتنگستات آمونیوم بررسی شده است. نمونه های پاراتنگستات آمونیوم با شیب حرارتی 0C/min 1 و 33/0 تحت جریان 20% متان در هیدروژن حرارت داده شدند. نمونه ها در فواصل دمایی مشخص بیرون آورده شده و مورد آزماشهای توزین، تعیین چگالی، تعیین سطح ویژه (BET) پراش پرتوایکس (XRD) و میکروسکوپی الکترونی روبشی (SEM) قرار گرفتند. نتایج حاکی از مرحله مهم تشکیل فاز W و افزایش ناگهانی سطح ویژه در حدود 0C 550 است. در دماهای بالاتر با تبدیل تدریجی W به W2C و بعد از آن WC تغییر چندانی در سطح ویژه ایجاد نمی شود. تشکیل رسوب کربن آمورف به علت متاناسیون حداقلی را در حول و حوش 0C 750 نشان می دهد. نرخ افزایش دمای C0/min 33/0 نسبت به C0/min 1 به جز در دماهای C0 850-650 تاثیر چندانی بر نانوساختار محصولات ندارد، اما میکروساختار آنها را دستخوش تغییرات کمتری می کند.}, keywords_fa = {پاراتنگستات آمونیم,کاربید تنگستن نانوساختاری,کربوریزاسیون}, url = {https://jfe.ut.ac.ir/article_10239.html}, eprint = {https://jfe.ut.ac.ir/article_10239_ddff42bfc75b029a7c9fdb1c18415049.pdf} } @article { author = {بیابانکی, سیدامیررضا and جعفری, احمد}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Discontinuities such as joints and faults make jointed media. There are several methods for analysis of these media; numerical methods are the best of them. In this paper 3D modeling of jointed rock mass and excavation geometry algorithms have been programmed. This program is in fact a pre-processor to be used in conjunction with the numerical methods for jointed media such as Discrete Element Method (DEM) and Discontinuities Deformation Analysis (DDA). Attempts are made to improve the efficiency of computational process, in comparison with existing algorithms.}, keywords = {}, title_fa = {مدلسازی سه بعدی حفریات سنگی در محیطهای ناپیوسته و ارائه روش نوینی برای تعیین نوع تماس بین بلوکها}, abstract_fa = {توده سنگی که در آن فضاهای حفاری به وجود می آید به دلیل وجود ناپیوستگی هایی ماننده درزه ها و گسلها محیطی ناپیوسته تلقی می شود. روشهای مختلفی برای تحلیل چنین محیطهایی وجود دارد که بهترین آنها روش های عددی می باشد. الگوریتم هایی برای مدلسازی یک سیستم متشکل از بلوکهای سنگی به همراه تشخیص انواع تماس بین بلوکهای این سیستم در این مقاله ارائه می شود که به عنوان یک پیش پردازنده برای روشهای عددی اجزای مجزا (DEM) و آنالیز تغییر شکل ناپیوسته (DDA) به کار می روند . در این تحقیق تلاش شده است تا راه حل های ساده تری با کارایی بیشتر در مقایسه با روش های موجود ارائه شود.}, keywords_fa = {بلوکهای سنگی,تشخیص تماس,توده سنگ درزه دار,درزه و ناپیوستگی,محیطهای ناپیوسته}, url = {https://jfe.ut.ac.ir/article_10240.html}, eprint = {https://jfe.ut.ac.ir/article_10240_3a72928bbca88effa213ddcbcc867109.pdf} } @article { author = {مجدی, عباس and ظهیری, مسعود}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Grouting is the process in which external materials are injected into the soil and rock pores, improving its strength to fit both the long and short term engineering goals. Grouting is generally performed in soil in of order to increase its strength, prevent foundation soil settlement and create a water sealing curtain to prevent inadmissible water seepage into tunnels and underground structures. Generally, the viscous grout mixture which is injected under pressure during the grout process flows into cavities and joints until they are blocked by the larger grout particles; therefore it is crucial to determine the suitability of the cement particle size which penetrates a porous medium. In general, investigation and design of such projects are merely based on empirical equations. However, analysis of the grout process in soil must be based on mathematical equations. In this paper, a mathematical model is developed which calculates the diameter of effective pore space of the soils and is then extended in order to determine the optimal cement particle size for grouting purposes assuming that the cement and soil particle sizes are spherical.}, keywords = {}, title_fa = {تعیین اندازه بهینه ذرات سیمان جهت تزریق سیمانی در خاک}, abstract_fa = {تزریق فرآیند راندن و نهشته کردن ماده ای خارجی به درون خلل و فرج خاک و سنگ می باشد، به گونه ای که ویژگی های مهندسی خاک و سنگ مورد نظر برای سازگاری با اهداف کوتاه و بلند مدت مهندسی اصلاح گردد. تزریق در خاک برای افزایش مقاومت و با جلوگیری از نشست خاک پی و نیز جهت ایجاد پرده آب بند به منظور جلوگیری از نشت های غیر مجاز به داخل تونل ها یا فضاهای زیرزمینی صورت می گیرد. اصولا سیالی که تحت فشار تزریق می گردد مانند یک مایع ویسکوز در حفره ها و شکاف ها جریان می یابد تا اینکه عناصر بزرگتر مایع تزریق در شکاف‌ها بلوکه گردد. بنابراین مناسب بودن اندازه ذرات سیمان جهت نفوذ در خلل و فرج یک محیط متخلخل بسیار مهم است. برای طرح و بررسی این موضوع صرفا به معادلات تجربی استناد می گردد. حال آنکه به منظور تحلیل روند تزریق در خاک دستیابی به روابط ریاضی ضروری می باشد. در این راستا با محاسبه قطر فضای خالی موثر بین ذرات خاک از طریق روابط ریاضی بدست آمده در این مقاله و تعمیم آن برای تعیین اندازه بهینه ذرات سیمان، رابطه ای حاصل گردیده که با مفروض دانستن شکل کروی برای ذرات خاک و سیمان چگونگی فرآیند تزریق را تبیین می نماید.}, keywords_fa = {آمیزه تزریق,تزریق پذیری,خاک,سیمان,فضای خالی موثر}, url = {https://jfe.ut.ac.ir/article_10241.html}, eprint = {https://jfe.ut.ac.ir/article_10241_d6a743a57104e61c45d74de9bac5d02d.pdf} } @article { author = {نوروزی, غلامحسین and غلامی, سعید}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {The geophysical studies (IP, Rs and M) have been carried out in the region of Sonagil located at 15 kilometers east of the city of Harris, in the Eastern Azarbayjan province. The main rock types are highly altered tuffs and andesite. In the initial studies, porphyritic copper has been recognized as the probable ore mineral. Magnetic method has been applied to study structural geology and intrusive bodies which could be the origin of mineralization in this region. According to the results obtained from magnetic data, three zones have been recognized having high magnetic fields, which is probably due to the existence of andesites. To study the shape and depth of andesitic rocks, the Euler deconvolution has been used. The geoelectrical studies consisted of induced polarization and resistivity. The inversion modeling was applied to process the IP and Rs data. Finally, based on the anomalies obtained from the geophysical methods, the location of drilling and areas for development of exploration in future were proposed.}, keywords = {}, title_fa = {تحلیل و مدلسازی داده های ژئوفیزیکی (IP, Rs, M) در محل اندیس معدنی مس سوناجیل}, abstract_fa = {مطالعات ژئوفیزیکی به سه روش مغناطیس سنجی (M) مقاومت ویژه ظاهری (Rs) و بارپذیری (IP)، در منطقه سوناجیل، واقع در 15 کیلومتری شرق شهرستان هریس در استان آذربایجان شرقی و در محدوده‌ای به ابعاد 800× 2300 متر انجام شده است. واحدهای سنگی موجود در منطقه شامل توف و آندزیت می باشد که در اکثر قسمتها به شدت دگرسان شده‌اند. مطالعات اولیه، تیپ احتمالی کانی سازی را مس پورفیری تشخیص داده است. جهت بررسی پدیده های ساختمانی و یا توده‌های نفوذی که می توانند منشا کانی سازی باشند از روش مغناطیسی استفاده شده است. به این ترتیب در سه بخش، مناطقی با شدت میدان بالا تشخیص داده شد که احتمالا در ارتباط با توده هایی از جنس آندزیت می باشد. جهت بررسی شکل و موقعیت پدیده های ساختمانی و توده های نفوذی روش دیکانولوشن اولر مورد استفاده قرار گرفت. مطالعات ژئوالکتریک با آرایش الکترودی مستطیلی در کل منطقه و با آرایش دو قطبی – دوقطبی بر روی بیهنجاریهای بدست آمده از مرحله اول صورت گرفته است. از تکنیک های آمار کلاسیک، برای تشخیص حد آستانه‌ای در داده‌های بارپذیری و از ضریب همبستگی جهت پی بردن به ارتباط دو متغیر بارپذیری و مقاومت ویژه ظاهری استفاده گردید. آنگاه عملیات مدلسازی وارون سازی به روش هموار جهت پردازش داده‌های ژئوالکتریک به کار رفت. در نهایت با توجه به بیهنجاریهای به دست آمده از روشهای ژئوفیزیکی نقاطی جهت عملیات حفاری پیشنهاد شد.}, keywords_fa = {پلاریزاسیون القایی,دیکانولوشن اولر,مدلسازی معکوس,مغناطیس,مقاومت ویژه}, url = {https://jfe.ut.ac.ir/article_10242.html}, eprint = {https://jfe.ut.ac.ir/article_10242_9b6466624c161dbc56b2bf9d98991b7f.pdf} } @article { author = {آذر, بابک وکیلی and کلاهدوزان, محد and اولیازاده, منوچهر and سناجیان, رضا}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Column flotation is one of the enrichment methods which have been developed in a great deal in recent years due to a higher performance and less operating costs. In this method which is based on the movement of hydrophobic particles upward in a tall column, the recovery is improved. Also wash water introduced at the top of the column which cleans the froth will increase the grade. Adopting improved control will cause a better outcome for this process. However, this is difficult to achieve due to the lack of high accuracy measuring devices as well as complicated mathematical relationships among acting parameters of the cell and also unpredictable outcomes caused by interactions between different parts of the cell. In this article, fuzzy logic is used to control one of the parameters of the process, froth depth, and for instrumentation of a laboratory column cell. Using fhzzy logic as a controlling tool and wash water to clean the froth, recovery and grade were improved 23.39% and 43.28% respectively for a copper sulphide sample used in this study.}, keywords = {}, title_fa = {کنترل سلول فلوتاسیون ستونی آزمایشگاهی با استفاده از منطق فازی}, abstract_fa = {فلوتاسیون ستونی از جمله روشهایی است که طی سالیان اخیر به علت افزایش راندمان تولید و هزینه های اجرائی کمتر در مقیاس صنعتی، پیشرفت قابل ملاحظه ای را شاهد بوده است. در این روش که بر اساس حرکت مواد آبران به سمت سطح در طول ستون بلندتر انجام میگیرد میزان بازیابی بیشتر خواهد شد. وجود آب شستشو در راس ستون به منظور شستن کف خارج شده نیز باعث افزایش عیار می گردد. در این بین اعمال کنترل مناسب بر روی این فرایند باعث بهبود نتایج خواهد شد که در عمل به علت عدم وجود ابزار اندازه‌گیری با صحت زیاد و وجود روابط پیچیده ریاضی بین متغیرهای درون سلول و غیر قابل پیش بینی بودن مقادیر کمی حاصل از اندرکنشهای متغیرهای مختلف با دشواری مواجه است. در این مقاله چگونگی استفاده از منطق فازی جهت کنترل یکی از پارامترهای مهم سلول (ارتفاع سطح کف) و چگونگی ابزاربندی و اندازهگیری متغیرها جهت حصول این مهم آورده شده است. مطالعه موردی با استفاده از کانسنگ مس سولفوره معدن چهل کوره یزد، کنترل کننده فازی و آب شستشو در راس ستون انجام گرفت و در میزان راندمان عملیات و عیار مس به ترتیب 39/23% و 28/43% بهبود حاصل گردید.}, keywords_fa = {ابزاربندی,فلوتاسیون ستونی,متغیرهای کنترلی و مدیریتی,منطق فازی}, url = {https://jfe.ut.ac.ir/article_10243.html}, eprint = {https://jfe.ut.ac.ir/article_10243_be89c88b45209e732b346df1e50bc5a5.pdf} } @article { author = {پور, مجید عمید and شاهی, محمدحسن پنجه and دانش, حسین احمدی}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Design and optimization of Heat Exchanger Networks is encountered as an important task when designing an industrial process. This is due to the energy crisis in the past three decades as well as the importance of environmental protection in achieving sustainable development. Heat Exchanger Networks comprising either mixed materials of construction, different exchanger types, or exchangers with different pressure ratings are considered to be more complicated in terms of targeting and design procedures. In this article a new method has been introduced, which takes advantage of Total Decomposition (as a known technique) and Partial Decomposition that is new and developed in this research. Also, Total Annualized Cost is minimized by optimizing AT of the network. Having used this technique, design will not anymore suffer from the increase in utility consumption that was due to heat recovery reduction between the sub-networks. The new method has been applied to a popular case study, using different utility and exchanger cost laws and also various interest rates and plant life times. Comparison of the results with other methods shows a reasonable improvement in both Western and Middle Eastern countries.}, keywords = {}, title_fa = {استفاده از روشهای تجزیه کلی و جزئی در یکپارچه سازی شبکه مبدل های حرارتی مختلط با در نظر گرفتن عوامل اقتصادی}, abstract_fa = {در کار تحقیقاتی حاضر به منظور حل معضل بهینه سازی شبکه مبدل های حرارتی که به واسطه جریان های خورنده ناگزیر به استفاده از مبدل های ساخته شده از مواد خاص و مختلف هستند تکنیک تجزیه شبکه ها به دو بخش تجزیه کلی و تجزیه جزئی تقسیم می گردد که روش تجزیه جزئی برای اولین بار پیشنهاد شده است و اشکالاتی همچون حداقل نبودن هزینه سالیانه کلی به دلیل عدم استفاده از Tmin های بهینه و نیز افزایش مصرف بار حرارتی گرمایشی و سرمایشی زیر مجموعه ها بدلیل کاهش بازیافت حرارت که از قبل در مورد روش تجزیه کلی نیز مطرح بود، در هر دو روش برطرف گردیده است. در انتها با انتخاب یک مسئله معروف در این زمینه که در مقابالت پژوهشی و کارهای تحقیقاتی انجام شده قبلی مورد استفاده قرار گرفته است نتایج هر دو روش به ازاء عوامل اقتصادی مختلف مورد بررسی قرار گرفته اند. این عوامل عبارتند از : قیمت انرژی در بخش گرمایش و سرمایش، نرخ بهره و طول عمر مفید شبکه نتایج بدست آمده در انتهای این مقاله مبین این واقعیت هستند که استفاده از روش های تجزیه کلی و تجزیه جزئی در انتگراسیون شبکه مبدل های حرارتی علاوه بر اینکه به ازاء شرایط اقتصادی اروپا قابل هستند، در شرایط اقتصادی خاورمیانه و بخصوص ایران نیز از توجیه منطقی و قابل قبولی برخوردار می باشند.}, keywords_fa = {انتگراسیون فرایند,تجزیه شبکه,تکنولوژی پینچ,شبکه مبدل های حرارتی,مبدل مختلط}, url = {https://jfe.ut.ac.ir/article_10244.html}, eprint = {https://jfe.ut.ac.ir/article_10244_a162255ca25d84e9419e43e1b1e32da8.pdf} } @article { author = {فاطمی, شهره and یوسفی, مجتبی and ایوانی, جواد}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {Prediction of phase behavior of light and heavy hydrocarbons at high pressures has found many applications in industries and academic purposes, recently. In contrast with the classical equation of states, statistical EOS can better predict the phase behavior of hydrocarbons at critical and supercritical conditions, because of their theoretical base approach in thermodynamics. In this study, at first, SAFT EOS was studied and investigated, then by modification of dispersion term the Simplified SAFT equation was introduced. By correlation of vapor pressure and liquid density data of pure alkanes and C02, the model parameters of SAFT and SSAFT equations were obtained using the direct search optimization method of Nelder-Mead algorithm. The correlated parameters such as number of segments (m), interaction energy of the segments (u°/k) and segment diameter (6), were predicted by minimizing the objective function, which is the sum of relative error of vapor pressures and liquid densities. The results shows better fitness with experiments in SSAFT rather than SAFT equation ,and in comparison to Peng-Robinson EOS, they both presents better agreement with vapor pressures and liquid densities. In study of the mixtures, vapor liquid equilibria of some non- homogeneous binary mixtures are determined by SSAFT equation using pure component parameters in a broad range of temperatures to estimate binary interaction parameters (kij). Using P-T-X experimental data, this parameter have been optimized by Nelder-Mead algorithm at different temperatures. It is concluded that a quadratic function of temperature can better predict the phase behavior of the studied binary mixtures rather than a constant parameter in broad range of temperatures.}, keywords = {}, title_fa = {بهینه سازی پارامترهای معادله حالت آماری SSAFT در تعادل فازی پارافین های سبک و سنگین در فشارهای بالا با روش Nelder – Mead}, abstract_fa = {در تحقیق حاضر ابتدا برای هیدروکربنهای خالص سبک وسنگین معادلات آماری SAFT بررسی شده است. سپس با تغییر و ساده سازی پارامتر پراکندگی ‘ شکل ساده تری بنام معادله SSAFT حاصل شده و پارامترهای بهینه این دو معادله برای دسته ای از هیدروکربنهای سبک وسنگین با در نظر گرفتن نقاط آزمایشی و بکارگیر الگوریتم بهینه سازی Nelder-Mead بدست آمده و در شرایط یکسان مورد مقایسه قرا رگرفته است. این پارامترها شامل m تعداد سگمنت ها‘ u/k انرژی برهمکنش سگمنت ها و a قطر سگمنت می باشد. تابع هدف برای تعیین پارامترهای بهینه شامل کمینه کردن همزمان انحراف فشار بخار و دانسیته مایع می باشد. مقایسه نتایج نشان داده است. که اولا دقت معادله های آماری از معادله کلاسیک پنگ رابینسون (PR) بیشتر بوده است. که با توجه به دید میکروسکوپیک معادلات آماری چندان دور از انتظار نمی باشد. ثانیا معادله SSAFT نسبت به SAFTبا دقت بیشتری به نتایج تجربی نزدیک شده است. در این مقاله پس از تعیین پارامترهای مواد خالص ‘ تعادلات فازی سیستم مخلوط های دو جزئی هیدروکربنهای غیر یکسان با معادله آماری SSAFT و به کمک الگوریتم Nelder-Mead بهینه سازی شد و پارامتر برهمکنش دو جزئی (KIJ) در محدوده وسیعی از دما وکسر مولی اجزا‘ براساس داده های تجربی P_T_X تعیین گردید. نتایج نشان داده است. که پارامتر برهمکنش با دما تغییر می کند . به منظور استفاده از یک مدل در محدوده وسیعی از دما ‘ پارامترهای برهمکنش به صورت تابعی از دما رگرسیون شده است. نتیجه شد که معادله درجه دوم بر حسب دما نتایج بهتری رانسبت به حالت مستقل از دما نشان می دهد.}, keywords_fa = {الگوریتم Nelder-Mead,تعادل فازی,معادلات حالت آماری SAFT,هیدروکربنهای سبک و سنگین}, url = {https://jfe.ut.ac.ir/article_10245.html}, eprint = {https://jfe.ut.ac.ir/article_10245_00cb3fffba1d9f41dc21b4b456164b73.pdf} } @article { author = {نوذری, علی and فراهانی, فرهنگ جلالی}, title = {-}, journal = {University College of Engineering}, volume = {39}, number = {2}, pages = {-}, year = {2005}, publisher = {}, issn = {0803-1026}, eissn = {}, doi = {}, abstract = {A new solution method to the MBE using Genetic Algorithms (GA) is presented in this paper following by three different examples solved by this technique, as well. In this approach, the role of the aquifer models in solving the MBE has been discarded because of the uncertainties existing in the aquifer properties. The latter is an important source of error in the material balance calculations. This research shows that material balance calculations are still vigorous tools in reservoir engineering to understand the field dynamic performance, in spite of recent developed complex reservoir simulators.}, keywords = {}, title_fa = {روش جدید حل معادله موازنه مواد با استفاده از الگوریتم ژنتیکی جهت تعیین حجم هیدروکربن اولیه و عملکرد مخازن}, abstract_fa = {این مقاله روش جدیدی را برای حل معادله موازنه مواد با استفاده از تکنیک الگوریتم ژنتیکی معرفی می کند. این الگوریتم با قابلیتهایی که داراست توانایی این را دارد که معادله موازنه مواد را به تنهایی حل کرده و بدون فرض مدل آبده مستقیما مقدار هیدروکربن درجا و شارآب ورودی به مخزن را مشخص نماید. در روش های مرسوم حل معادله موازنه مواد از معادلات مدلهای آبده به عنوان یک معادله کمکی استفاده می شود و برای حل مدل آبده نیاز به استفاده از خواص آبده است. این خواص اغلب دارای عدم قطعیت هستند زیرا به دلیل هزینه های بالای حفاری، برای پارامترهای آبده، به اطلاعات تخمینی اکتفا می شود. این مطالعه به شرح این تکنیک جدید و بررسی چند مثال عملی می پردازد تا توانایی های غیر قابل انکار آن را در پرهیز از محاسبات زاید ریاضی و حذف مرحله حدس و خطا نشان دهد. یکی از موارد بررسی شده میدان نفتی کربناته واقع در جنوب غرب ایران می باشد.}, keywords_fa = {الگوریتم ژنیتک,موازنه مواد,نفت درجا}, url = {https://jfe.ut.ac.ir/article_10246.html}, eprint = {https://jfe.ut.ac.ir/article_10246_e825c5aecd0b32e2c062f3f9f8e72a11.pdf} }